Dell E6330 Owner's Manual

Dell Latitude E6330Owner's ManualRegulatory Model: P19SRegulatory Type: P19S001

10

2Removing and Installing ComponentsThis section provides detailed information on how to remove or install the components from your computer.Recommende

Removing the ExpressCard1. Follow the procedures in Before Working Inside Your Computer.2. Press in on the ExpressCard to release it from the computer

3. Remove the battery from the computer.Installing the Battery1. Slide the battery into its slot until it clicks into place.2. Follow the procedures i

4. Slide the SIM card out from the computer.Installing the SIM Card1. Slide the SIM card into its compartment.2. Install the battery.3. Follow the pro

4. Slide the hard drive out of the computer.5. Remove the screw that secures the hard-drive bracket to the hard drive.6. Pull the hard-drive bracket o

Installing the Hard Drive1. Install the hard-drive isolations on the hard drive.2. Attach the hard-drive bracket to the hard drive.3. Tighten the scre

5. Remove the screw that secures the drive latch to the optical drive.6. Remove the drive latch from the optical drive.7. Remove the screws that secur

9. Pull and remove the drive caddy away from the optical drive.Installing the Optical Drive1. Secure the optical drive caddy to the optical drive.2. S

4. Lift the base cover to remove it from the computer.Installing the Base Cover1. Place the base cover to align with the screw holes on the computer.2

Notes, Cautions, and WarningsNOTE: A NOTE indicates important information that helps you make better use of your computer.CAUTION: A CAUTION indicates

5. Lift up to remove the keyboard trim from the unit.Installing the Keyboard Trim1. Align the keyboard trim to its slot.2. Press along the sides of th

6. Lift and turn the keyboard to access the keyboard cable.7. Disconnect the keyboard cable from the system board.8. Remove the keyboard from the comp

10. Remove the keyboard cable from the keyboard.Installing the Keyboard1. Connect the keyboard cable and secure it to the keyboard using the tape.2. C

Removing the Bluetooth Module1. Follow the procedures in Before Working Inside Your Computer.2. Remove the battery.3. Remove the base cover.4. Disconn

7. Remove the bluetooth module from the computer.8. Disconnect the bluetooth cable from the bluetooth module.Installing the Bluetooth Module1. Connect

4. Pry the securing clips away from the memory module until it pops up.5. Remove the memory module from its connector on the system board by drawing t

3. Disconnect the coin-cell battery cable from the system board.4. Remove the coin-cell battery from the computer.Installing the Coin-Cell Battery1. P

3. Remove the screws that secure the palmrest assembly to the base of the computer.4. Remove the screws that secure the palmrest assembly to the front

7. Disconnect the power LED cable from the system board.8. Lift the palmrest up and away from the computer.Installing the Palmrest1. Align the palmres

Removing the Media Board1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) SD cardb) ExpressCardc) batteryd) hard drivee) op

Contents1 Working on Your Computer... 7Before Work

Installing the Media Board1. Place the media board in its compartment.2. Tighten the screws to secure the media board.3. Connect the media-board cable

4. Remove the screws that secure the ExpressCard cage to the computer.5. Remove the ExpressCard cage from the computer.Installing the ExpressCard Cage

Removing the Speakers1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) SD cardb) ExpressCardc) batteryd) hard drivee) optic

6. Remove the speakers from the computer.Installing the Speakers1. Align the speakers to their original position and tighten the screws to secure the

3. Remove the screws that secure the display-hinge covers to the computer.4. Remove the display-hinge covers from the computer.Installing the Display

Removing the Display Assembly1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) SD cardb) ExpressCardc) batteryd) hard drive

6. Remove the screws that secure the Low-Voltage Differential Signaling (LVDS) support bracket.7. Lift up and remove the LVDS support bracket.8. Disco

10. Remove the display assembly from the computer.Installing the Display Assembly1. Route the antennae cables through the opening on the system board.

Removing the System Board1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) SD cardb) ExpressCardc) batteryd) hard drivee) o

5. Disconnect the speaker cable from the system board.6. Remove the screws that secure the system board to the computer.7. Lift the left edge of syste

Installing the ExpressCard Cage...

9. Remove the system board from the computer.Installing the System Board1. Connect the power connector cable to the system board.2. Tighten the screws

Removing the Heat Sink1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) SD cardb) ExpressCardc) batteryd) hard drivee) opti

5. Remove the heat sink from the system board.Installing the Heat Sink1. Place the heat sink into its original position on the system board.2. Tighten

Removing the Power Connector Port1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) SD cardb) ExpressCardc) batteryd) hard d

5. Remove the power connector port from the computer.Installing the Power-Connector Port1. Place the power-connector port on the computer.2. Place the

Removing the Input/Output (I/O) Board1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) SD cardb) ExpressCardc) batteryd) ha

3. Install:a) system boardb) display assemblyc) display hinge coversd) media boarde) palmrestf) bluetooth moduleg) keyboardh) keyboard trimi) base cov

5. Remove the display bezel from the display assembly.Installing the Display Bezel1. Place the display bezel onto the display assembly.2. Starting fro

5. Flip and place the display panel over.6. Peel off the LVDS cable connector tape and disconnect the LVDS cable from the display panel.7. Remove the

Removing the Camera and Microphone Module1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) batteryb) display bezel3. Remove

Enhanced Pre-Boot System Assessment (ePSA) Diagnostics...73Device Status L

4. Install:a) display bezelb) battery5. Follow the procedures in After Working Inside Your Computer.Removing the LED Board1. Follow the procedures in

6. Remove the screw that secures the LED board to the LED-board support plate.7. Remove the LED board from the LED-board support plate.Installing the

Removing the Display-Hinge Walls1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) SD cardb) ExpressCardc) batteryd) hard dr

5. Peel off the adhesive tape that secures the antenna cables to the display assembly.6. Remove the antenna cables from the opening in the right displ

Installing the Display-Hinge Walls1. Place both the display-hinge walls on the panel.2. Insert the antenna cables into their opening on the right disp

3. Remove the screw that secures the left display hinge to the display assembly.4. Remove the left display hinge wall out of the display assembly.5. R

Removing the LVDS and Camera Cable1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) SD cardb) ExpressCardc) batteryd) hard

5. Pry up the LVDS and camera cable from the display assembly.6. Remove the LVDS and camera cable from the display assembly cover.Installing the LVDS

58

3Docking Port InformationThe docking port is used for connecting the laptop to a docking station (optional).1. Docking Port59

6

60

4System SetupSystem Setup enables you to manage your computer hardware and specify BIOS‐level options. From the System Setup, you can:• Change the NVR

Keys Navigation<Enter> Allows you to select a value in the selected field (if applicable) or follow the link in the field.Spacebar Expands or co

Option Description• Enabled• Enabled w/PXE (Default Setting)Parallel Port Allows you to define and set how the parallel port on the docking station op

Option Description• Enable SMART Reporting — This option is disabled by default.USB Configuration Allows you to define the USB configuration. The opti

Table 4. VideoOption DescriptionLCD Brightness Allows you to set the panel brightness when the ambient sensor is Off.Optimus Allows you to enable or d

Option DescriptionDefault Setting: Enable CPU XD SupportComputrace Allows you to activate or disable the optional Computrace software The options are

Option DescriptionHyper-Thread Control Allows you to enable or disable the HyperThreading in the processor.Default Setting: EnabledTable 7. Power Mana

Option Description• Custom Charge — you can set the percentage to which the battery must charge.NOTE: All charging modes may not be available for all

Table 9. Virtualization SupportOption DescriptionVirtualization Specifies whether a Virtual Machine Monitor (VMM) can utilize the additional hardware

1Working on Your ComputerBefore Working Inside Your ComputerUse the following safety guidelines to help protect your computer from potential damage an

Updating the BIOS It is recommended to update your BIOS (system setup), on replacing the system board or if an update is available. For laptops, ensur

NOTE: If the password jumper is disabled, the existing System Password and Setup Password is deleted and you need not provide the system password to l

72

5DiagnosticsIf you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical assistance. The purpose of r

Turns on steadily or blinks to indicate battery charge status.Turns on when wireless networking is enabled.The device status LEDs are usually located

6Technical SpecificationsNOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. F

AudioInternal high-definition audioExternal microphone-in/stereo headphones/external speakers connectorSpeakers twoInternal speaker amplifier 1 W (RMS

DisplayLatitude E6330 13.3"Dimensions:Latitude E6230Height 300.90 mm (11.84 inches)Width 180.00 mm (7.08 inches)Diagonal 317.30 mm (12.49 inches)

Battery• 6-cell (58 WHr) Lithium-ion batteryDimensions:3-cellDepth 29.97 mm (1.18 inches)Height 19.80 mm (0.78 inch)Width 208.00 mm (8.19 inches)6-cel

PhysicalLatitude E6230 Latitude E6330Height 22.40 mm to 24.70 mm (0.88 inch to 0.97 inch)25.40 mm to 30.10 mm (1 inch to 1.19 inches)Width 309.00 mm (

6. Close the display and turn the computer upside-down on a flat work surface.NOTE: To avoid damaging the system board, you must remove the main batte

80

7Contacting DellNOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill,

After Working Inside Your ComputerAfter you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turn