Dell Latitude 10 - ST2 Owner's Manual

Dell Latitude 10 – ST2Owner's ManualRegulatory Model: T05GRegulatory Type: T05G001

Pen and Touch SettingsUsing the stylus, you can adjust how quickly you tap the screen when you double-tap the screen. It also allows you define the sp

Touch UsageOne of the key advantages of the Tablet PC is the ability to easily switch from pen input to touch input.When you use Touch Mode , a transl

12

3Removing and Installing ComponentsThis section provides detailed information on how to remove or install the components from your computer.Recommende

Figure 2. Internal View1. docking board2. coin-cell battery3. speaker4. system board5. front camera6. rear camera7. SmartCard reader/WWAN card (WWAN c

Installing the Battery1. Slide the battery into its slot until it clicks into place.2. Follow the procedures in After Working Inside Your Computer.Rem

4. Pry and release the tabs that secure the base cover by following the arrow sequence in the diagram.5. Pry and lift the tabs that secure the base co

6. Lift the retention clasp in an upward direction and release the fingerprint reader cable outward to remove it from the system board. Lift the base

Installing the Front Camera1. Place the camera module in its slot on the computer.2. Tighten the screw to secure the camera module to the computer.3.

5. Un-route the speaker cables on the right-hand side of the computer and lift up to release the right speaker from the computer.6. Un-route the speak

Notes, Cautions, and WarningsNOTE: A NOTE indicates important information that helps you make better use of your computer.CAUTION: A CAUTION indicates

Installing the Speakers1. Place the right and the left speakers in their slot.2. Route the speaker cables on the chassis.3. Tighten the screws to secu

Installing the SmartCard Reader 1. Place the SmartCard reader into its slot.2. Tighten the screws to secure the SmartCard reader to the system board.3

4. Disconnect the screws that secure the WWAN card to the system board and lift it up to remove it from the computer.Installing the Wireless Wide Area

5. Remove the docking board from the computer and disconnect the home-button board cable.Installing the Docking Board1. Connect the home-button board

f) front camerag) docking board3. Disconnect the LVDS and docking board flex cables.4. Remove the screws that secure the system board to the computer.

e) SmartCard readerf) base coverg) battery4. Follow the procedures in After Working Inside Your Computer.Removing the Rear Camera1. Follow the procedu

3. Follow the procedures in After Working Inside Your Computer.Removing the Coin-Cell Battery1. Follow the procedures in Before Working Inside Your Co

5. Follow the procedures in After Working Inside Your Computer.27

28

4System SetupSystem Setup enables you to manage your computer hardware and specify BIOS‐level options. From the System Setup, you can:• Change the NVR

ContentsNotes, Cautions, and Warnings...21 Working on

Keystroke Actionconnected to an optional external USB keyboard)On Screen Mouse PointerUse this to navigate the System Setup by using your finger or an

Table 5. Boot SequenceOption FunctionFile Browser Add Boot Option Displays the order that the BIOS searches devices when trying to find an operating s

Option DescriptionClick OK after entering the password details.System Password Allows you to set, change, or delete the computer password (previously

Option DescriptionAdmin Setup Lockout Allows you to enable or disable the option to enter setup when an admin password is set.• Enable Admin Setup Loc

Option Description• Disabled - Does not allow the system to power on by special LAN signals when it receives a wake-up signal from the LAN or wireless

5Troubleshooting Your ComputerYou can troubleshoot your computer using indicators like Diagnostic Lights, Beep Codes, and Error Messages during the op

2. The computer will start up and begin running the ePSA utility automatically.3. During the testing process, you will be prompted to answer a YES or

4. Press the Security Button (<Ctrl> + <Alt> + <Del>) to click OK once the tests are completed.5. The volume up and down buttons can

Code Cause and Troubleshooting StepsSystem board failure, covers BIOS corruption or ROM error2 No RAM detectedNo memory detected3 Chipset Error (North

Code Cause and Troubleshooting Steps6 Video BIOS test failureVideo card failure7 CPU - cache test failureProcessor failure8 DisplayDisplay failureTrou

Installing the Docking Board...

In Windows 8, verify if the Tablet PC Components check box (in Windows Features) is selected after successfully installing the Wacom software bundle.I

6SpecificationsSpecificationsNOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your compute

VideoVideo type integratedData bus internalVideo controller Intel Graphics Media AcceleratorCommunicationsNetwork adapter USB 2.0 based Gigabit LAN vi

BatteryHeight 5.48 mm (0.22 inch) 10.03 mm (0.39 inch)Width 86.50 mm (3.40 inches) 86.50 mm (3.40 inches)Weight 220.00 g (0.49 lb) 373.00 g (0.82 lb)V

EnvironmentalAltitude (maximum):Operating–16 m to 3048 m (–50 to 10,000 ft)Non-operating –15.2 m to 10,668 m (–50 ft to 35,000 ft)Airborne contaminant

7Contacting DellContacting DellNOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, pack

1Working on Your ComputerBefore Working Inside Your ComputerUse the following safety guidelines to help protect your computer from potential damage an

NOTE: To avoid damaging the system board, you must remove the main battery before you service the computer.7. Remove the main battery.8. Turn the comp

2OverviewYour Dell Latitude 10-ST2 tablet is built for business with easy management and security. It provides:• world class security• easy management

Using a Stylus in a TabletThe stylus allows you to actively navigate through the menus. You can use it as a mouse and also as a pen.Using the Stylus a

2. Go to Folder options.3. Click View.4. Under Advanced settings , select the Use check boxes to select items check box, and then click OK.Entering Te