Dell M6348 User's Guide Page 40
- Page / 158
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
40 Switching Configuration
discard Discard frames with unlearned source addresses.
max Configure the maximum addresses that can be learned
on the port.
trap Sends SNMP Traps, and specifies the minimum time
between consecutive traps.
console(config-if-1/g18)#port security
Example #2: Show Port Security
console#show ports security ?
addresses Addresses.
ethernet Ethernet port.
port-channel Link Aggregation interface.
<cr> Press enter to execute the command.
Example #3: Show Port Security on an Interface
console#show ports security ethernet 1/g18
Port Status Action Maximum Trap Frequency
----- -------- ----------------- ------- ------- ---------
1/g18 Locked Discard 100 Disable 30
Link Layer Discovery Protocol
The Link Layer Discovery Protocol (LLDP) feature allows individual interfaces on the switch to advertise
major capabilities and physical descriptions. Network managers can view this information and identify
system topology and detect bad configurations on the LAN.
LLDP has separately configurable transmit and receive functions. Interfaces can transmit and receive
LLDP information.
CLI Examples
Example #1: Set Global LLDP Parameters
Use the following sequence to specify switch-wide notification interval and timers for all LLDP
interfaces.
console#configure
console(config)#lldp ?
notification-interval Configure minimum interval to send remote data
change notifications.
timers Configure the LLDP global timer values.
console(config)#lldp notification-interval ?
- Configuration Guide 1
- Notes, Notices, and Cautions 2
- Contents 3
- About this Document 9
- Additional Documentation 10
- System Configuration 11
- CLI Example 12
- Configuration Scripting 13
- 14 System Configuration 14
- Outbound Telnet 16
- 18 System Configuration 18
- DEF GH I 19
- 20 System Configuration 20
- Port Description 21
- Storm Control 21
- 24 System Configuration 24
- Admin State column): 24
- Switching Configuration 25
- VLAN Configuration Example 26
- Example #1: Create Two VLANs 27
- 28 Switching Configuration 28
- Web Interface 29
- IP Subnet and MAC-Based VLANs 29
- Protocol-Based VLANs 30
- Private Edge VLANs 31
- IGMP Snooping 32
- IGMP Snooping Querier 33
- 36 Switching Configuration 36
- Port Mirroring 38
- Port Security 39
- Link Layer Discovery Protocol 40
- DHCP Snooping 44
- Switching Configuration 45 45
- Figure 3-3. DHCP Binding 45
- 48 Switching Configuration 48
- 50 Switching Configuration 50
- Port Aggregator 51
- Simple Mode Operation 53
- <intf-list> 55
- <Group Id> 58
- CLI Command Reference 59
- • Port Channel Commands: 61
- • Radius commands: 61
- • SNMP Commands: 61
- • SSH commands: 61
- 62 Switching Configuration 62
- • System Management Commands: 62
- • TACACS commands: 62
- • VLAN Commands 62
- • Web Server Commands: 62
- Packet Flow Sampling 64
- 66 Switching Configuration 66
- Routing Configuration 67
- 68 Routing Configuration 68
- Enable VRRP for the switch: 71
- OSPF Concepts and Terms 74
- OSPF Routers and LSAs 75
- Metrics and Route Selection 75
- 78 Routing Configuration 78
- 82 Routing Configuration 82
- Routing Information Protocol 84
- Route Preferences 87
- Using Equal Cost Multipath 89
- Loopback Interfaces 90
- IP Helper 92
- 96 Routing Configuration 96
- Device Security 97
- Guest VLAN 101
- CLI Examples 101
- Operation in the Network 103
- Access Control Lists (ACLs) 106
- MAC ACLs 107
- ACL Configuration Process 108
- IP ACL CLI Examples 108
- Device Security 109 109
- MAC ACL CLI Examples 110
- 112 Device Security 112
- RADIUS Configuration Examples 113
- Device Security 115 115
- TACACS+ Configuration Example 116
- Captive Portal 117
- Captive Portal Configuration 118
- Web Page Customization 120
- Captive Portal Status 121
- Captive Portal Statistics 122
- 126 Device Security 126
- Overview 127
- Interface Configuration 127
- Interface 0/1 Interface 0/1 128
- Interface 0/2 128
- Device 2 129
- 132 IPv6 132
- DHCPv6 pool configuration: 132
- Quality of Service 133
- Queue configuration 134
- Queue Management Type 134
- Quality of Service 135 135
- Port1/0/10 136
- Differentiated Services 137
- Quality of Service 141 141
- Multicast 143
- IGMP Configuration 144
- IGMP Proxy 144
- Prune messages 146
- Example: PIM-SM 149
- Example: PIM-DM 150
- Auto Config 151
- Assignment of TFTP Server 152
- Obtaining a Config File 152
- Saving a Configuration 154
- Specifying a Default Router 155
- Other Functions 156
- 158 Utility 158
Related products and manuals for Network switches Dell M6348
Network switches Dell M6220 User's Guide
(27 pages)
(27 pages)
Network switches Dell N3048 Specifications
(70 pages)
(70 pages)
Network switches Dell 3548 Manual
(5 pages)
(5 pages)
Network switches Dell 5548P User's Guide
(728 pages)
(728 pages)
Network switches Dell 5524 User's Guide
(728 pages)
(728 pages)
Network switches Dell 5524P User's Guide
(728 pages)
(728 pages)
Network switches Dell S5000 Setup Guide
(78 pages)
(78 pages)
Network switches Dell Nexus B22 User Manual
(16 pages)
(16 pages)
© 2020, manymanuals.com. All rights reserved. | 0.114 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals