Dell PowerConnect 5448, 3Y NBD User's Guide Page 188
- Page / 444
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
188 Configuring System Information
Defining LLDP MED Port Settings
The MED Port Settings contains parameters for assigning LLDP network policies to specific ports.
To open the MED Port Settings page, click System
→ LLDP-MED → Port Settings in the tree view.
Figure 6-76. MED Port Settings
The MED Port Settings page contains the following fields:
•
Port
— Displays the port on which LLDP-MED is enabled or disabled.
•
Enable LLDP-MED
— Indicates if LLDP-MED is enabled on the selected port. The possible field
values are:
Checked
— Enables LLDP-MED on the port.
Unchecked
— Disables LLDP-MED on the port. This is the default value.
- User Guide 1
- Notes, Cautions and Warnings 2
- Contents 3
- 4 Contents 4
- 6 Contents 6
- 8 Contents 8
- 10 Contents 10
- 12 Contents 12
- Introduction 13
- Features 14
- Introduction 15 15
- Layer 2 Features 16
- VLAN Supported Features 17
- Link Aggregation 18
- Layer 3 Features 19
- Quality of Service Features 19
- Device Management Features 20
- Security Features 21
- Locked Port Support 22
- Additional CLI Documentation 23
- 24 Introduction 24
- Hardware Description 25
- Device Ports 26
- Physical Dimensions 27
- LED Definitions 27
- System LEDs 28
- Hardware Components 29
- Reset Button 30
- Ventilation System 30
- Installation Precautions 31
- Site Requirements 32
- Unpacking 32
- Mounting the Device 33
- Connecting the Device 34
- Crossover 35
- Back Panel 35
- Power Connect 36
- Rear View 36
- Port Default Settings 37
- MDI/MDIX 38
- Flow Control 38
- Back Pressure 38
- Configure the Terminal 40
- Booting the Device 40
- Initial Configuration 43
- Wizard Step 1 44
- Wizard Step 2 45
- Wizard Step 3 46
- Wizard Step 4 46
- Wizard Step 5 46
- Advanced Configuration 47
- Configuring Login Banners 52
- Startup Procedures 52
- Software Download 54
- Erase FLASH File 54
- Password Recovery 54
- System Image Download 55
- Understanding the Interface 59
- Device Representation 60
- Information Buttons 61
- Device Management Buttons 61
- Starting the Application 62
- <IP address 63
- Privileged EXEC Mode 64
- Global Configuration Mode 64
- Interface Configuration Mode 65
- CLI Examples 66
- Viewing Device Information 67
- Figure 6-2. Asset 68
- Defining System Information: 69
- Initiating a Telnet Session: 69
- Defining System Time Settings 71
- Selecting a Clock Source 75
- Defining Local Clock Settings 75
- ][zone acronym] 76
- offset] 76
- Viewing the Versions Page 79
- Resetting the Device 80
- Configuring SNTP Settings 81
- Broadcast Time Information 82
- Defining SNTP Servers 86
- Figure 6-11. SNTP Servers 87
- Adding an SNTP Server 88
- Modifying an SNTP Server 89
- Deleting the SNTP Server 90
- Defining SNTP Interfaces 91
- Adding an SNTP Interface 92
- Managing Logs 93
- Enabling Logs: 95
- Displaying RAM Log Table 97
- Displaying the Log File Table 99
- Viewing Login History 101
- Sending Logs to a Server: 105
- Defining a New Server: 105
- Defining Device IP Addresses 107
- IPv6 Syntax 108
- IPv6 Prefixes 108
- Defining IPv4 Interfaces 109
- Adding an IPv4 Interface 110
- Deleting IP Addresses 111
- Adding DHCP Clients 113
- Defining IPv6 Interfaces 115
- Adding an IPv6 Interface 117
- Figure 6-29. Add IPv6 Address 118
- Interface page 119
- Defining IPv6 Default Gateway 120
- CLI Command Description 122
- Defining IPv6 ISATAP Tunnels 123
- Defining IPv6 Neighbors 125
- Figure 6-33. IPv6 Neighbors 126
- Adding an IPv6 Neighbor 127
- Modifying Neighbor Parameters 128
- Deleting Neighbors 128
- Viewing the IPv6 Routes Table 129
- Adding a DNS Server 133
- Removing DNS Servers 134
- Defining Default Domains 135
- Mapping Domain Host 136
- Adding Host Domain Names 137
- Configuring ARP 139
- Displaying the ARP Table 141
- Deleting ARP Table Entry 141
- Running Cable Diagnostics 142
- Performing a Cable Test 144
- Managing Device Security 147
- Activating a Profile 148
- Adding an Access Profile 149
- Removing a Rule 152
- Managing Passwords 161
- Defining Password Management 162
- Viewing Active Users 164
- Defining a New User: 166
- Deleting Users: 167
- Defining Line Passwords 168
- Defining Enable Passwords 170
- Defining TACACS+ Settings 171
- Figure 6-64. TACACS+ Settings 172
- Adding a TACACS+ Server 173
- Displaying the TACACS+ Table 174
- Removing a TACACS+ Server 174
- Figure 6-67. RADIUS Settings 176
- Defining RADIUS Parameters: 178
- Adding a RADIUS Server: 178
- Configuring LLDP and LLDP-MED 181
- Defining LLDP Properties 182
- Defining LLDP Port Settings 183
- Figure 6-71. Port Settings 184
- Adding an MED Network Policy: 187
- → LLDP-MED → Neighbors 192
- Defining SNMP Parameters 194
- Enabling SNMP Notifications 195
- Defining SNMP View Settings 197
- Adding a View 199
- Defining SNMP Access Control 200
- Defining SNMP Groups 202
- Displaying the Access Table 202
- Removing SNMP Groups 203
- Assigning SNMP User Security 203
- Adding Users to a Group 205
- Defining Communities 207
- Defining a New Community 209
- Displaying all Communities 210
- Deleting Communities 210
- Defining Notification Filters 212
- Adding SNMP Filters 213
- Displaying the Filter Table 213
- Removing a Filter 214
- Adding a new Trap Recipients 217
- Managing Files 220
- Downloading Files 221
- Firmware Download 222
- Active Image 222
- Configuration Download 222
- Uploading Files 224
- Configuration Upload 225
- Software Image Upload 225
- Copying Files 227
- Managing Device Files 229
- Defining Advanced Settings 230
- Optimizing iSCSI 232
- Global Parameters page 234
- Managing iSCSI Targets 236
- Removing Targets 237
- Monitoring iSCSI Sessions 238
- Configuring Network Security 241
- MAC Based Authentication 242
- Port Based Authentication 243
- Figure 7-3. Multiple Hosts 248
- Authenticating Users 251
- Configuring Port Security 252
- Figure 7-7. Port Security 253
- Defining a Locked Port 254
- ACL Overview 256
- Adding ACEs to IP based ACLs 259
- Adding IP based ACLs 260
- ACEs Associated with IP-ACL 261
- Removing an IP based ACL 261
- Removing an IP based ACE 261
- Adding MAC based ACLs 265
- Removing a MAC based ACL 266
- Removing a MAC based ACE 266
- Defining ACL Binding 267
- Removing ACL Bindings 268
- Configuring DHCP Snooping 269
- DHCP Snooping global 271
- Figure 7-17. VLAN Settings 272
- Defining Trusted Interfaces 273
- DHCP Snooping Trusted 275
- Interfaces 275
- Querying the Database 276
- Removing a Database Entry 276
- Clearing the Dynamic Database 276
- DHCP Snooping Binding 277
- Database 277
- Configuring Ports 278
- Defining Port Parameters 280
- Modifying Port Parameters 280
- Configuring Load Balancing 284
- Defining LAG Parameters 286
- Modifying LAG Parameters 286
- 2-3 287
- Enabling Storm Control 289
- Figure 7-26. Storm Control 290
- Figure 7-28. Port Mirroring 293
- Configuring Address Tables 295
- Adding a Static MAC Address 296
- Viewing Dynamic Addresses 298
- Redefining the Aging Time 299
- Configuring GARP 301
- Defining GARP Timers 302
- Defining STP Global Settings 304
- Defining STP Port Settings 308
- Enabling STP on a Port 310
- Modifying STP Port Properties 310
- Displaying the STP Port Table 310
- Defining STP LAG Settings 312
- Enabling RSTP 316
- Figure 7-36. MSTP Settings 318
- Configuring VLANs 323
- Defining VLAN Members 324
- Adding New VLANs 325
- VLAN Port Membership Table 326
- Deleting a VLAN 327
- Defining VLAN Ports Settings 331
- Assigning Port Settings 332
- Defining VLAN LAG Settings 334
- Assigning VLAN LAG Settings: 335
- Displaying the VLAN LAG Table 335
- Defining VLAN Protocol Groups 337
- Adding Protocol Ports 339
- Configuring GVRP 340
- Enabling GVRP on the Device 341
- GVRP Global Parameters page 342
- Configuring Voice VLANs 343
- Configuring Port Settings 348
- Voice VLAN port settings 348
- Defining OUIs 349
- Aggregating Ports 351
- Defining LACP Parameters 352
- Defining LAG Membership 354
- Multicast Forwarding Support 355
- IGMP Snooping 366
- Unregistered Multicast 371
- Viewing Statistics 375
- Viewing Counter Summary 376
- Viewing Interface Statistics 377
- Receive Statistics 378
- Transmit Statistics 378
- Viewing Statistics 379 379
- Viewing Etherlike Statistics 380
- Viewing GVRP Statistics 383
- Resetting GVRP Statistics 384
- Viewing Statistics 385 385
- Viewing EAP Statistics 387
- Resetting the EAP Statistics 388
- Viewing RMON Statistics 389
- Viewing Statistics 393 393
- Viewing Statistics 395 395
- Defining Device RMON Events 396
- Viewing Statistics 397 397
- Adding an RMON Event 398
- Modifying an RMON Event 398
- Deleting RMON Event Entries 398
- Viewing the RMON Events Log 399
- Defining RMON Device Alarms 401
- Adding an Alarm Table Entry 402
- Displaying the Alarm Table 403
- Deleting an Alarm Table Entry 403
- Viewing Charts 404
- Displaying Port Statistics 405
- Viewing LAG Statistics 406
- Displaying LAG Statistics 407
- Viewing the CPU Utilization 409
- CoS Services 412
- Enabling Quality of Service: 413
- Enabling Trust: 414
- Defining Bandwidth Settings 416
- Defining Queue Settings 419
- Mapping CoS Values to Queues 422
- Mapping DSCP Values to Queues 423
- Figure 9-8. DSCP to Queue 424
- Restoring default values: 425
- Device Specifications 427
- Operating Conditions 428
- Device Memory Specifications 428
- Feature Specifications 429
- Additional Switching Features 430
- Device Management 430
- System Features 430
- Glossary 431
- Glossary 433 433
- Combo Ports 433
- Glossary 435 435
- Image File 435
- Glossary 437 437
- Glossary 439 439
- Index 441 441
- 442 Index 442
- Index 443 443
- 444 Index 444
Related products and manuals for Network switches Dell PowerConnect 5448, 3Y NBD
Network switches Dell S5000 Setup Guide
(78 pages)
(78 pages)
Network switches Dell Nexus B22 User Manual
(16 pages)
(16 pages)
© 2020, manymanuals.com. All rights reserved. | 0.102 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals