Dell OpenManage Server Administrator Version 7.0 User Manual Page 120
- Page / 302
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
120 omconfig: Managing Components Using the Instrumentation Service
omconfig chassis currents or omconfig mainsystem currents
NOTE: This command is no longer available through Server Administrator.
omconfig chassis fans or omconfig mainsystem fans
Use the omconfig chassis fans or omconfig mainsystem fans command to
set fan probe warning thresholds. As with other components, you can view
both warning and failure threshold values, but you cannot set failure
thresholds. The system manufacturer sets the minimum and maximum
failure thresholds.
Valid Parameters for Fan Warning Thresholds
Table 4-5 s h ows the v alid parameters for setting fan warning thresholds:
Default Minimum and Maximum Warning Thresholds
NOTE: Systems that contain ESM3, ESM4, and BMC capabilities do not allow you to
set warning threshold values to default values.
To set both the upper and lower fan warning threshold values to the
recommended default value, type:
UEFI Boot Settings attribute=UefiBootSeq sequence=aliasname1,
aliasname2,..... aliasnameN
Table 4-5. omconfig chassis fans or omconfig chassis fans
name=value pair Description
index=<n> Number of the probe or probe index (must specify.)
warnthresh=default Sets minimum and maximum warning thresholds to default.
minwarnthresh=<n> Minimum warning threshold.
maxwarnthresh=<n> Maximum warning threshold.
Table 4-4. BIOS Setup Settings on PowerEdge yx2x Systems
(continued)
Group name=value pair 1
attribute=
name=value pair 2
setting=
- Command Line 1
- Interface Guide 1
- Notes and Cautions 2
- Contents 3
- 4 Contents 4
- Using the Instrumentation 6
- 8 Contents 8
- 10 Contents 10
- 12 Contents 12
- 9 Working With CLI Command 13
- 14 Contents 14
- Introduction 15
- New Features 17
- Command Prompts 18
- Primary CLI Commands 19
- Success Messages 20
- Failure Messages 21
- Command Syntax Overview 23
- Using the omhelp Command 25
- 28 Using the omhelp Command 28
- <command level 2> -? 37
- Commands 39
- Parameters Description 42
- PowerEdge yx2x systems 45
- Critical 47
- Administrator 58
- Commands for Viewing Logs 67
- <component name> 72
- Output Attributes Description 74
- Example Command Output 77
- System Attributes 82
- Remote Access Information 83
- Processor 83
- Memory Array 83
- Firmware 84
- NOTE: You cannot change 91
- NOTE: The 103
- (continued) 112
- NOTE: This option is 128
- Default Warning Thresholds 130
- NOTE: extipmiusergroup 143
- Command Result Description 151
- Defining Alert Actions 153
- Available Alert Actions 154
- Example Current Probe Actions 157
- Example Fan Probe Actions 157
- Commands for Clearing Logs 158
- Action Description 160
- Event Name Description 160
- Severity 164
- Example Recovery Commands 167
- Example Shutdown Commands 168
- Ownership Values 171
- Adding Lease Information 177
- Adding Outsource Information 180
- Adding Owner Information 181
- Adding Support Information 184
- Adding System Information 186
- Adding Warranty Information 187
- Using the Storage Management 191
- Command Elements 192
- Syntax Description 193
- 196 omreport storage Commands 196
- NOTE: If a physical disk 196
- Replacing 196
- 198 omreport storage Commands 198
- Required 199
- Command Levels 199
- (1, 2, 3) 199
- 200 omreport storage Commands 200
- Required Command Levels 201
- 202 omreport storage Commands 202
- NOTE: For SCSI controllers 202
- Required Command Levels (1 203
- 2, 3) and name=value pair 203
- 204 omreport storage Commands 204
- Report Commands 205
- NOTE: This command is not 205
- Required Command 206
- Levels (1, 2, 3) 206
- Optional name= 206
- 208 omreport storage Commands 208
- 210 omconfig storage Commands 210
- Example for SAS Controllers 212
- Command 225
- Optional name=value pairs 225
- Complete Syntax 226
- Example Syntax 226
- Example Syntax to reconfigure 234
- CAUTION: The 239
- 240 omconfig storage Commands 240
- For SAS Controllers 245
- Parameter Specification 248
- Description 248
- RAID 10) 250
- Omconfig Enclosure Commands 264
- degree Celsius, type: 269
- List (lst) 285
- Table (tbl) 286
- Custom Delimited Format (cdv) 287
- Index 289 289
- Index 291 291
- Index 293 293
- Index 295 295
- Index 297 297
- Index 299 299
- Index 301 301
- Index 302 302
Related products and manuals for Servers Dell OpenManage Server Administrator Version 7.0
Servers Dell PowerVault DL2000 User Manual
(188 pages)
(188 pages)
(58 pages)
Servers Dell PowerEdge R510 User Manual
(24 pages)
(24 pages)
Servers Dell PowerEdge C5220 How to Use
(60 pages)
(60 pages)
Servers Dell PowerEdge C6100 Owner's Manual
(160 pages)
(160 pages)
Servers Dell PowerEdge R415 Owner's Manual
(188 pages)
(188 pages)
Servers Dell PowerEdge SL300 User Manual
(41 pages)
(41 pages)
Servers Dell POWEREDGE R515 Owner's Manual
(194 pages)
(194 pages)
Servers Dell PowerEdge 800 Service Manual
(87 pages)
(87 pages)
Servers Dell DR4100 User Manual
(119 pages)
(119 pages)
Servers Dell R2 User Manual
(34 pages)
(34 pages)
Servers Dell PowerEdge R720 White Paper
(17 pages)
(17 pages)
Servers Dell R2 User Manual
(32 pages)
(32 pages)
Servers Dell PowerEdge C6145 Owner's Manual
(250 pages)
(250 pages)
© 2020, manymanuals.com. All rights reserved. | 0.157 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals