Dell Lifecycle Controller 2 Version 1.3.0 Service Manual download pdf (Page 219)

<n1:ReturnValue>4096</n1:ReturnValue>

</n1:ApplyAttributes_OUTPUT>

19.4.2 Polling Job Completion

Run the Get() command to check the progress of the ApplyAttributes() method. It polls for job

completion. This method takes the InstanceID from the earlier section ( 19.3.1) as input. The

JobStatus

value is either “Successful” or “Failed”. If the job failed, the

Message

value contains

detailed error information on the cause of the failure.

Run the Get() command on DCIM_LifecycleJob with the following parameters and syntax:

EXAMPLE:

wsman get http://schemas.dmtf.org/wbem/wscim/1/cim-

schema/2/root/dcim/DCIM_LifecycleJob

?InstanceID=$INSTANCEID -h $IPADDRESS -V -v -c dummy.cert -P 443 -u $USERNAME

-p $PASSWORD –j utf-8 –y basic

The input parameter is the InstanceID from the output of the ApplyAttributes() method. An example

InstanceID

is as follows:

InstanceID = JID_001293705757

OUTPUT:

<n1:DCIM_LifecycleJob>

<n1:InstanceID>JID_001300815142</n1:InstanceID>

<n1:JobStartTime>TIME_NA</n1:JobStartTime>

<n1:JobStatus>Completed</n1:JobStatus>

<n1:JobUntilTime>TIME_NA</n1:JobUntilTime>

<n1:Message>NA</n1:Message>

<n1:MessageID>NA</n1:MessageID>

<n1:Name>iDRACConfig:iDRAC.Embedded.1</n1:Name>

<n1:PercentComplete>100</n1:PercentComplete>

</n1:DCIM_LifecycleJob>

19.4.3 Set Attribute Verification

To verify the changes made to the attributes, enumerate the

DCIM_iDRACCardEnumeration

class.

For more information, see Section 19.1.

OUTPUT #2:

<n1:DCIM_iDRACCardEnumeration>

<n1:AttributeDisplayName>Nic Enable</n1:AttributeDisplayName>

<n1:AttributeName>Enable</n1:AttributeName>

<n1:CurrentValue>Enabled</n1:CurrentValue>

<n1:DefaultValue>Enabled</n1:DefaultValue>

<n1:Dependency xsi:nil="true"/>

<n1:DisplayOrder>0</n1:DisplayOrder>

<n1:FQDD>iDRAC.Embedded.1</n1:FQDD>

<n1:GroupDisplayName>NIC</n1:GroupDisplayName>

<n1:GroupID>NIC.1</n1:GroupID>

<n1:InstanceID>iDRAC.Embedded.1#NIC.1#Enable</n1:InstanceID>

<n1:IsReadOnly>false</n1:IsReadOnly>

<n1:PossibleValues>Disabled</n1:PossibleValues>

<n1:PossibleValues>Enabled</n1:PossibleValues>

</n1:DCIM_iDRACCardEnumeration>

<n1:DCIM_iDRACCardEnumeration>

<n1:AttributeDisplayName>Virtual Media Attached

</n1:AttributeDisplayName>

<n1:AttributeName>Attached</n1:AttributeName>

1 2 ... 214 215 216 217 218 219 220 221 222 223 224 ... 239 240

Comments to this Manuals

No comments

Dell Lifecycle Controller 2 Version 1.3.0 Service Manual Page 219

Comments to this Manuals

Related products and manuals for Software Dell Lifecycle Controller 2 Version 1.3.0