Dell POWEREDGE M1000E User Manual Page 99
- Page / 126
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Fabric Watch Administrator’s Guide 79
53-1002752-01
Examples of the sysMonitor command
8
Examples of the sysMonitor command
The following sections provide specific examples for the Environment class, CPU, and memory.
Environment class settings
Temperature settings are switch-dependent and there is no need to alter them. The default alarm
configuration, sending alerts to the error log and SNMP, is sufficient. See “Environment monitoring
setting guidelines” on page 76 for more information.
Pausing and continuing monitoring
To pause the monitoring of a class, area, and port or index, enter the sysMonitor command using
the following parameters.
NOTE
You cannot specify all for all classes but you can specify all for all areas.
switch:admin> sysmonitor --pause | --continue env -area temp
Displaying the threshold of the system areas
The temperature area refers to the ambient temperature inside the switch, in degrees Celsius.
Temperature sensors monitor the switch in case the temperature rises to levels at which damage to
the switch might occur.
Enter the sysMonitor command using the following parameters:
switch:admin> sysmonitor --show env -area temp index
Example of configuring the temperature threshold
1. Enter the sysMonitor command using the following parameters:
switch:admin> sysmonitor --config env -area temp -highth -value 99
-trigger above -action raslog
2. Apply the changes:
switch:admin> sysmonitor --apply env -area temp -action_level cust
-thresh_level cust
Resource class settings
The flash area of the Resource class monitors the percentage of compact flash memory used on
the system.
Displaying the system flash parameters
Enter the sysMonitor command using the following parameters:
switch:admin> sysmonitor --show resource -area flash
- Fabric Watch 1
- Document History 3
- Contents 5
- Chapter 7 Port Monitoring 7
- Chapter 8 System Monitoring 8
- 53-1002752-01 10
- About This Document 15
- What’s new in this document 16
- Document conventions 17
- Notes, cautions, and warnings 18
- Key terms 18
- Additional information 19
- Getting technical help 19
- Document feedback 20
- Fabric Watch overview 22
- Role-based access control 22
- Fabric Watch licensing 22
- Event behavior configuration 23
- Alert configuration 23
- Time base configuration 24
- Monitoring 24
- Post-processing of messages 24
- Switch monitoring components 25
- Security monitoring 26
- SFP monitoring 26
- Port monitoring 26
- System resource monitoring 27
- Logical switch support 28
- Fabric Watch event settings 29
- SNMP traps 30
- RASlog (switch event) 30
- Fabric Watch audit messages 31
- Data values 31
- • Fabric 32
- • Security 32
- • E_Port (Port subclass) 32
- • VE_Port (Port subclass) 32
- Fabric Watch Thresholds 33
- Threshold triggers 34
- Above event trigger 35
- Below event trigger 35
- Audit and RASlog messages 35
- Time bases 36
- Fabric Watch alarm behavior 37
- Elements 40
- Class Description 41
- Fabric Watch Activation 43
- FIGURE 6 Example OID tree 47
- Fabric Watch Configuration 49
- Disabling an e-mail alert 52
- Enabling an e-mail alert 52
- Sending a test e-mail message 53
- Notification configuration 54
- FW: Alarms are enabled 55
- Area Description 58
- Fabric class default settings 59
- Security class areas 60
- Threshold state 61
- SFP class areas 63
- • Send an SNMP alarm 66
- • Log a RASlog message 66
- • Send an e-mail alert 66
- Configuration recommendation 67
- 16 Gbps and QSFP monitoring 68
- Monitoring the SFP and QSFP 69
- Security classes 72
- Port Monitoring 75
- Port class default settings 77
- Port configuration 78
- Using the nosave command 79
- Port type: physical port 79
- <[slot/]port> 81
- E_Port class default settings 82
- • Area: Loss of Signal Count 84
- Port fencing 89
- Port fencing configuration 90
- Enabling port fencing 91
- Disabling port fencing 91
- Port fencing requirements 92
- System Monitoring 95
- 76 53-1002752-01 96
- Resource class settings 97
- Environment class settings 99
- CPU and memory 100
- Switch monitoring 101
- Switch status policy planning 102
- Monitor Health factors 103
- FRU monitoring 104
- Recommended FRU settings 106
- In this chapter 107
- • Polling Interval 108
- • Usage Limit 108
- • No. of Retries 108
- Configuring threshold traits 109
- Configuring threshold alarms 110
- Displaying alarms 113
- Enabling the e-mail alert 114
- Disabling the e-mail alert 115
- Fabric Watch Reports 117
- Switch Health report 119
- Switch Status Policy report 120
- Port Detail report 121
- Report item Description 122
Related products and manuals for Computer Accessories Dell POWEREDGE M1000E
(27 pages)
(94 pages)© 2020, manymanuals.com. All rights reserved. | 1.410 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals