Dell Vostro 5470 Owner's Manual Page 1

Dell Vostro 5470Owner's ManualRegulatory Model: P41GRegulatory Type: P41G002

Installing the Base Cover1. Place the base cover to align with the screw holes on the computer.2. Tighten the screws to secure the base cover to the c

5. Lift and remove the battery from the computer.11

Installing the Battery1. Place the battery into its slot until it clicks into place.2. Connect the battery cable to its connector on the system board.

Installing the Hard Drive1. Place the hard drive assembly into its slot on the computer.2. Install:a) batteryb) base cover3. Follow the procedures in

Installing the Coin-Cell Battery1. Place the coin-cell battery into its slot on the computer.2. Route the coin-cell battery cable along the routing ch

Removing the mSATA SSD Card1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) base coverb) battery3. Remove the screw that s

4. Lift and remove the left system fan from the computer.5. Disconnect the right system fan cable from its connector on the system board. Peel away th

6. Remove the screws that secure the right system fan to the system board.7. Lift and remove the right system fan from the computer.17

Installing the System Fan1. Place the right system fan into its original position in the system board and affix the system board flex cable.2. Tighten

4. Lift up the heatsink and remove from the computer.19

Notes, Cautions, and WarningsNOTE: A NOTE indicates important information that helps you make better use of your computer.CAUTION: A CAUTION indicates

Installing the Heatsink1. Place the heatsink into its original position on the system board.2. Tighten the screws to secure the heatsink to the system

b) displayc) keyboardd) touchpade) cameraf) coin-cell batteryg) WLANh) Finger printer4. Remove the screws that secure the system board to the chassis.

5. Remove the system board from the computer.22

Installing the System Board1. Place the system board into its original position on the chassis.2. Tighten the screws to secure the system board to the

4. Lift the speaker assembly along with the routing cable and remove the speakers from the computer.24

Installing the Speakers1. Place the speakers into its original position on the computer.2. Route the speaker cable along the routing channel.3. Connec

4. Remove the screws that secure the display hinges to the system board. Lift and move the system base panel away from the display hinges to facilitat

Installing the Display Assembly1. Align the base panel of the computer to the display hinges.2. Install the screws that secure the display hinges to t

4. Pry on the plastic caps that cover the display bezel screws and remove them.5. Remove the screws that secure the screws to the display bezel.28

6. Pry along the inner edges of the display bezel and remove the display bezel.29

Contents1 Working on Your Computer... 5Before Work

Installing the Display Bezel1. Align the display bezel by pressing along the edges.2. Install the screws that secure the display bezel.3. Install the

Installing the Display Panel1. Align the display panel to the display assembly by pressing along the edges.2. Install the screws that secure the displ

Installing the Camera1. Align the camera to the base panel .2. Connect the camera cable to the camera.3. Install :a) batteryb) base coverc) display as

3System SetupSystem Setup OverviewSystem Setup allows you to:• change the system configuration information after you add, change, or remove any hardwa

NOTE: For most of the system setup options, changes that you make are recorded but do not take effect until you restart the system.Table 1. Navigation

Table 2. MainSystem Time Re-sets the time on the computer's internal clock.System Date Re-sets the date on the computer's internal calendar.

Intel Rapid Start Technology Enable or disable Inter Rapid Start Technology.Deafult: EnableMiscellaneous Devices These fields let you enable or disabl

4TroubleshootingEnhanced Pre-Boot System Assessment (ePSA) DiagnosticsThe ePSA diagnostics (also known as system diagnostics) performs a complete chec

Battery Charge LED Off/Hibernate StandbyDischarging when Battery charge is <=10%Off Blinking WhiteDevice Status LightsTurns on when you turn on the

5SpecificationsTechnical SpecificationNOTE: Offerings may vary by region. For more information regarding the configuration of your computer, click Sta

3 System Setup... 33System S

Feature DescriptionVolume controls Program menus and keyboard shortcut keysTable 11. VideoFeature DescriptionVideo type UMA/DISVideo Controller:UMA In

Feature DescriptionWidth 326.18 mm (12.84 inches)Diagonal 14.0"Active area (X/Y) 309.4 mm (12.18 inches) x 173.95 mm (6.84 inches)Maximum resolut

Feature DescriptionNon-Operating 0 ℃ to 65 ℃Coin-cell battery LI 3V 83 MAHTable 19. AC AdapterFeature DescriptionType AC adapterInput voltage 90 ~ 264

Non-Operating –15.2 m to 10,668 m (–50 ft to 35,000 ft)Airborne contaminant level G2 or lower as defined by ISA - S71.04 – 198543

44

6Contacting DellContacting DellNOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, pack

1Working on Your ComputerBefore Working Inside Your ComputerUse the following safety guidelines to help protect your computer from potential damage an

CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the c

2Removing and Installing ComponentsThis section provides detailed information on how to remove or install the components from your computer.Recommende

7. hard drive8. system fan9. system board10. memory module11. heatsinkRemoving the Base Cover1. Follow the procedures in Before Working Inside Your Co

4. Lift and remove the base cover from the computer.9