Dell Brocade 5100 User's Guide Page 34
- Page / 126
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
14 Fabric Watch Administrator’s Guide
53-1002752-01
Threshold triggers
2
In-between buffer values
The below high threshold is the term used to configure “in between” buffer values, as shown in
Figure 1. In this example, the high threshold value is 5 and the buffer value is 1. Therefore, the
“in-between” boundary value is 4. Enter the portThConfig command using the following
parameters.
portthconfig --set port -area crc -highth -value 5 -trigger below -action raslog
-buffer 1
Above high threshold
Above action = 5
_______________________________________________________________________________
HIGH THRESHOLD, BUFFER = 1
_______________________________________________________________________________
Low action
Below high threshold
In-between
Above low threshold
Above action
______________________________________________________________________________
LOW THRESHOLD, BUFFER=1
______________________________________________________________________________
Low action
Below low threshold
FIGURE 1 In-between buffer values
Threshold triggers
This section describes how Fabric Watch compares a fabric element’s data value against a
threshold value to determine whether or not to trigger an event. It describes how a specified buffer
zone affects event triggering.
For Fabric Watch to monitor data values for one of the following conditions, the alarm setting must
be set to a nonzero value.
- Fabric Watch 1
- Document History 3
- Contents 5
- Chapter 7 Port Monitoring 7
- Chapter 8 System Monitoring 8
- 53-1002752-01 10
- About This Document 15
- What’s new in this document 16
- Document conventions 17
- Notes, cautions, and warnings 18
- Key terms 18
- Additional information 19
- Getting technical help 19
- Document feedback 20
- Fabric Watch overview 22
- Role-based access control 22
- Fabric Watch licensing 22
- Event behavior configuration 23
- Alert configuration 23
- Time base configuration 24
- Monitoring 24
- Post-processing of messages 24
- Switch monitoring components 25
- Security monitoring 26
- SFP monitoring 26
- Port monitoring 26
- System resource monitoring 27
- Logical switch support 28
- Fabric Watch event settings 29
- SNMP traps 30
- RASlog (switch event) 30
- Fabric Watch audit messages 31
- Data values 31
- • Fabric 32
- • Security 32
- • E_Port (Port subclass) 32
- • VE_Port (Port subclass) 32
- Fabric Watch Thresholds 33
- Threshold triggers 34
- Above event trigger 35
- Below event trigger 35
- Audit and RASlog messages 35
- Time bases 36
- Fabric Watch alarm behavior 37
- Elements 40
- Class Description 41
- Fabric Watch Activation 43
- FIGURE 6 Example OID tree 47
- Fabric Watch Configuration 49
- Disabling an e-mail alert 52
- Enabling an e-mail alert 52
- Sending a test e-mail message 53
- Notification configuration 54
- FW: Alarms are enabled 55
- Area Description 58
- Fabric class default settings 59
- Security class areas 60
- Threshold state 61
- SFP class areas 63
- • Send an SNMP alarm 66
- • Log a RASlog message 66
- • Send an e-mail alert 66
- Configuration recommendation 67
- 16 Gbps and QSFP monitoring 68
- Monitoring the SFP and QSFP 69
- Security classes 72
- Port Monitoring 75
- Port class default settings 77
- Port configuration 78
- Using the nosave command 79
- Port type: physical port 79
- <[slot/]port> 81
- E_Port class default settings 82
- • Area: Loss of Signal Count 84
- Port fencing 89
- Port fencing configuration 90
- Enabling port fencing 91
- Disabling port fencing 91
- Port fencing requirements 92
- System Monitoring 95
- 76 53-1002752-01 96
- Resource class settings 97
- Environment class settings 99
- CPU and memory 100
- Switch monitoring 101
- Switch status policy planning 102
- Monitor Health factors 103
- FRU monitoring 104
- Recommended FRU settings 106
- In this chapter 107
- • Polling Interval 108
- • Usage Limit 108
- • No. of Retries 108
- Configuring threshold traits 109
- Configuring threshold alarms 110
- Displaying alarms 113
- Enabling the e-mail alert 114
- Disabling the e-mail alert 115
- Fabric Watch Reports 117
- Switch Health report 119
- Switch Status Policy report 120
- Port Detail report 121
- Report item Description 122
Related products and manuals for Network switches Dell Brocade 5100
Network switches Dell M1000E User Manual
(103 pages)
(103 pages)
Network switches Dell Brocade 5300 User's Guide
(934 pages)
(934 pages)
Network switches Dell Force10 White Paper
(57 pages)
(57 pages)
Network switches Dell DNN1548P Datasheet
(2 pages)
(2 pages)
Network switches Dell 210-ABVI Datasheet
(4 pages)
(4 pages)
Network switches Dell 210-AEDM Datasheet
(3 pages)
(3 pages)
Network switches Dell 210-AADO Datasheet
(2 pages)
(2 pages)
Network switches Dell 210-ADUW Datasheet
(4 pages)
(4 pages)
Network switches Dell 210-AEIK Datasheet
(3 pages)
(3 pages)
© 2020, manymanuals.com. All rights reserved. | 0.168 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals