Dell PowerConnect W-AirWave 7.4 User Manual download pdf (Page 25)

Dell PowerConnect W-AirWave 7.4 | Best Practices Guide AMP and Dell PowerConnect W-Series Integration Strategies | 25

Figure 10 Verify IP Address on APs/Devices > Monitor Page

Verify that there is a SNMPv2 community string that matches the SNMP Trap community string on the

controller.

(Controller-Name) # show snmp community

SNMP COMMUNITIES

----------------

COMMUNITY ACCESS VERSION

--------- ------ -------

public READ_ONLY V1, V2c

(Controller-Name) # #show snmp trap-host

SNMP TRAP HOSTS

---------------

HOST VERSION SECURITY NAME PORT TYPE TIMEOUT RETRY

---- ------- ------------- ---- ---- ------- -----

10.2.32.4 SNMPv2c public 162 Trap N/A N/A

Verify firewall port 162 (default) is open between AMP and the controller.

Validate traps are making it into AMP by issuing the following commands from AMP command line.

[root@AMP ~]# qlog enable snmp_traps

[root@AMP ~]# tail -f /var/log/amp_diag/snmp_traps

1241627740.392536 handle_trap|2009-05-06 09:35:40 UDP: [10.2.32.65]->[10.51.5.118]:-

32737 sends trap: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (127227800) 14 days,

17:24:38.00 SNMPv2-MIB::snmpTrapOID.0 = OID: SNMPv2-

SMI::enterprises.14823.2.3.1.11.1.2.1106 SNMPv2-SMI::enterprises.14823.2.3.1.11.1.1.60

= Hex-STRING: 07 D9 05 06 09 16 0F 00 2D 08 00 SNMPv2-

SMI::enterprises.14823.2.3.1.11.1.1.5.0 = Hex-STRING: 00 1A 1E 6F 82 D0 SNMPv2-

SMI::enterprises.14823.2.3.1.11.1.1.6.0 = STRING: aruba-apSNMPv2-

SMI::enterprises.14823.2.3.1.11.1.1.1.0 = Hex-STRING: 00 1A 1E C0 2B 32 SNMPv2-

SMI::enterprises.14823.2.3.1.11.1.1.56.0 = INTEGER: 2 SNMPv2-

SMI::enterprises.14823.2.3.1.11.1.1.17.0 = STRING: aruba-124-c0:2b:32 SNMPv2-

SMI::enterprises.14823.2.3.1.11.1.1.18.0 = INTEGER: 11 SNMPv2-

SMI::enterprises.14823.2.3.1.11.1.1.58.0 = STRING: http://10.51.5.118/screens/wmsi/

reports.html?mode=ap&bssid=00:1a:1e:6f:82:d0

Ensure you disable qlogging after testing as it could negatively impact AMP performance if left turned on:

[root@AMP ~]# qlog enable snmp_traps

NOTE: You will see many IDS and Auth Traps from this command. AMP only processes a small subset of these Traps which display

within AMP. The Traps that AMP does process are listed above.

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 47 48

No comments

Dell PowerConnect W-AirWave 7.4 User Manual Page 25