Dell OptiPlex 9020 Owner's Manual

Dell OptiPlex 9020 Small Form FactorOwner's ManualRegulatory Model: D07SRegulatory Type: D07S001

Installing the Front Bezel1. Insert the hooks along the bottom edge of the front bezel into the slots on the chassis front.2. Push the bezel toward th

4. Pull the release lever away from the expansion card until you release the securing tab from the dent in the card. Then, ease the card up and out of

Installing The Expansion Card1. Insert the expansion card into the connector on the system board and press down to secure it in place.2. Install the c

Installing the WLAN Card1. Place the WLAN card on the connector and press down.2. Press the latch to secure the WLAN card.3. Place the antenna puck on

6. Repeat steps 3 to 5 to remove the second optical drive (if available).Installing the Optical Drive1. Insert the optical drive into the bracket.2. S

4. Slide the blue drive-cage handle toward unlock position and lift the hard drive cage from the computer.Installing the Drive Cage1. Place the drive

Removing the Hard Drive1. Follow the procedures in Before Working Inside Your Computer.2. Remove the:a) coverb) optical drivec) drive cage3. Press the

4. Install the:a) drive cageb) optical drivec) cover5. Follow the procedures in After Working Inside Your Computer.Removing the Speaker1. Follow the p

• Memory modules of different sizes can be mixed (for example, 2 GB and 4 GB). But, all populated channels must have identical configurations.• Memory

4. Pry and remove the system fan away from the grommets securing it to the front of the computer. Then, press the grommets inward along the slots and

Notes, Cautions, and WarningsNOTE: A NOTE indicates important information that helps you make better use of your computer.CAUTION: A CAUTION indicates

Removing the Power Switch1. Follow the procedures in Before Working Inside Your Computer.2. Remove the:a) coverb) front bezelc) optical drived) drive

3. Install the:a) drive cageb) optical drivec) front bezeld) cover4. Follow the procedures in After Working Inside Your Computer.Removing the Input/Ou

Installing the Input/Output (I/O) Panel1. Insert the I/O panel into the slot on the chassis front.2. Slide the I/O panel to secure it to the chassis.3

5. Remove the screws that secure the power supply to the back of the computer.6. Push in on the blue release tab and slide the power supply towards th

Installing the Power Supply1. Place the power supply in the chassis and slide towards the back of the computer to secure it.2. Tighten the screws secu

Installing the Coin-Cell Battery1. Place the coin-cell battery into its slot on the system board.2. Press the coin-cell battery downward until the rel

Installing the Heat Sink Assembly1. Place the heat-sink assembly into the chassis.2. Tighten the captive screws to secure the heat-sink assembly to th

Installing the Processor1. Insert the processor into the processor socket. Ensure the processor is properly seated.2. Gently lower the processor cover

System Board ComponentsThe following image displays the system board layout.1. power connector2. processor socket3. system fan connector4. memory modu

4. Remove the screws that secure the system board to the chassis.5. Turn the hex screw counter clockwise and remove from the system board.6. Remove th

Contents1 Working on Your Computer... 5Before Work

30

3System SetupSystem Setup enables you to manage your computer hardware and specify BIOS‐level options. From the System Setup, you can:• Change the NVR

Keys Navigation<Enter> Allows you to select a value in the selected field (if applicable) or follow the link in the field.Spacebar Expands or co

Table 3. System ConfigurationOption DescriptionIntegrated NIC Allows you to enable or disable the integrated network card. You can set the integrated

Option DescriptionSMART Reporting This field controls if the hard drive errors for the integrated drives are reported during system startup. This tech

Option Description• System Password Min• System Password MaxPassword Bypass Allows you to bypass the System Password and the internal HDD password pro

Option DescriptionThis option is set to Enable by default.Admin Setup Lockout Allows you to enable or disable the option to enter setup when an admin

Option Description• 1• 2Intel SpeedStep Allows you to enable or disable the Intel SpeedStep mode of the processor. This option is enabled by default.C

Option Description• Disabled - The system will not automatically power up.• Every Day - The system will power up every day at the time you specified a

Table 8. POST BehaviorOption DescriptionNumlock LED Specifies if the NumLock function can be enabled when the system boots. This option is enabled by

Removing the Heat Sink Assembly...

Option DescriptionNOTE: This field is only relevant when the Integrated NIC control in the System Configuration group is set to Enabled with ImageServ

Updating the BIOS It is recommended to update your BIOS (system setup), on replacing the system board or if an update is available. For laptops, ensur

CAUTION: The password features provide a basic level of security for the data on your computer.CAUTION: Anyone can access the data stored on your comp

NOTE: If you change the System and/or Setup password, re-enter the new password when promoted. If you delete the System and/or Setup password, confirm

44

4DiagnosticsIf you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical assistance. The purpose of r

46

5Troubleshooting Your ComputerYou can troubleshoot your computer using indicators like Diagnostic Lights, Beep Codes, and Error Messages during the op

Amber LED State Description3,7 some other failure with messages on screenBeep CodeThe computer can emit a series of beeps during start-up if the displ

Error Message DescriptionDecreasing available memoryOne or more memory modules may be faulty or improperly seated. Re-install the memory modules and,

1Working on Your ComputerBefore Working Inside Your ComputerUse the following safety guidelines to help protect your computer from potential damage an

Error Message DescriptionMemory double word logic failure at address, read value expecting valueA memory module may be faulty or improperly seated. Re

Error Message DescriptionTime-of-day not set-please run the System Setup programThe time or date stored in System Setup does not match the computer cl

52

6SpecificationsNOTE: Offerings may vary by region. For more information regarding the configuration of your computer, click Start (Start icon) → Help

Table 19. NetworkFeature SpecificationIntegrated Intel I217LM Ethernet capable of 10/100/1000 Mb/s communicationTable 20. System InformationFeature Sp

Feature SpecificationMini-Tower noneSmall Form Factor noneUltra Small Form Factor up to one Mini CardTable 23. DrivesFeature SpecificationExternally A

Feature SpecificationVideo• 15-pin VGA connector• two 20-pin DisplayPort connectorsNOTE: Available video connectors may vary based on the graphics car

Feature SpecificationSystem Fan one 5-pin connectorFront panel control:Mini-Tower• one 6–pin connector• two 20–pin connectorSmall Form Factor• one 6-p

Feature SpecificationGreen — a good 100 Mbps connection exists between the network and the computer.Orange — a good 1000 Mbps connection exists betwee

Feature SpecificationStorage 5 percent to 95 percent (non-condensing)Maximum vibration:Operating 0.26 GRMSStorage 2.20 GRMSMaximum shock:Operating 40

CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the c

60

7Contacting DellNOTE: Dell provides several online and telephone-based support and service options. If you do not have an active Internet connection,

2Removing and Installing ComponentsThis section provides detailed information on how to remove or install the components from your computer.Recommende

6. drive cage7. optical drive8. power switch9. input/output (I/O) Panel1. memory module2. speaker3. front bezel4. system fanRemoving the Cover1. Follo

Installing the Cover1. Place the cover on the chassis.2. Press down on the cover till it clicks into place.3. Follow the procedures in After Working I