Dell PowerConnect W-Airwave 7.5 User Manual Page 285
- Page / 338
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Dell PowerConnect W-AirWave 7.5 | User Guide Using VisualRF | 273
Location Calculation Timer Settings
To tune the frequency for calculating device locations within the VisualRF UI, navigate to the Location
Calculation Timer Settings section. The available settings are described in Table 144:
Table 144 Location Calculation Timer Settings Section of VisualRF > Setup
Setting Default Description
Legacy Laptop Min/Max
(sec)
90/360 This timer determines how often to calculate the location for legacy laptop devices.
Taken with the data samples the calculation acts as follows:
After the minimum timer (default is 90 seconds), check to see if the number of data
samples received from all APs that hear this client are greater than or equal to the
number of samples setting for legacy laptop devices (default of 3 data samples).
If so (Yes to question above), then recalculate the client device's location based on
the samples received.
If not (No to the question above), then wait until the number of sample setting is met
before recalculating. If the number of samples is never met, wait until the maximum
timer (default is 360 seconds) and then recalculate.
Legacy Laptop Number
of Samples
3 See definition above.
Laptop Min/Max (sec) 90/360 This timer determines how often to calculate the location for laptop (non-legacy)
devices. Taken with the data samples the calculation acts as follows:
After the minimum timer (default is 90 seconds), check to see if the number of data
samples received from all APs that hear this client are greater than or equal to the
number of samples setting for legacy laptop devices (default of 3 data samples).
If so (Yes to question above), then recalculate the client device's location based on
the samples received.
If not (No to the question above), then wait until the number of sample setting is met
before recalculating. If the number of samples is never met, wait until the maximum
timer (default is 360 seconds) and then recalculate.
Laptop Number of
Samples
3 See definition above.
Phone Min/Max (sec) 60/240 This timer determines how often to calculate the location of phones. Taken with the
data samples the calculation acts as follows:
After the minimum timer (default is 60 seconds), check to see if the number of data
samples received from all APs that hear this client are greater than or equal to the
number of samples setting for legacy laptop devices (default of 3 data samples).
If so (Yes to question above), then recalculate the client device's location based on
the samples received.
If not (No to the question above), then wait until the number of sample setting is met
before recalculating. If the number of samples is never met, wait until the maximum
timer (default is 240 seconds) and then recalculate.
Phone Number of
Samples
3 See definition above.
RFID Min/Max (sec) 30/120 This timer determines how often to calculate the location of RFIDs (such as devices
with tag readers for tracking). Taken with the data samples the calculation acts as
follows:
After the minimum timer (default is 30 seconds), check to see if the number of data
samples received from all APs that hear this client are greater than or equal to the
number of samples setting for legacy laptop devices (default of 4 data samples).
If so (Yes to question above), then recalculate the client device's location based on
the samples received.
If not (No to the question above), then wait until the number of sample setting is met
before recalculating. If the number of samples is never met, wait until the maximum
timer (default is 120 seconds) and then recalculate.
RFID Number of
Samples
4 See definition above.
Scale Min/Max (sec) 500/2000
- Dell PowerConnect W 1
- AirWave 7.5 1
- Copyright 2
- Contents 3
- Chapter 1 13
- VisualRF 14
- Master Console and Failover 15
- Administrative Roles 16
- Chapter 2 17
- Getting Started 18
- Upgrading AirWave 21
- AirWave Navigation Basics 22
- Status Section 23
- Navigation Section 24
- Main Tab Description Subtabs 25
- Activity Section 26
- Help Links in the UI 27
- Common List Settings 27
- Buttons and Icons 28
- Getting Started with AirWave 29
- Figure 5 AirWave Login Form 30
- Chapter 3 31
- Customizing Columns in Lists 32
- Resetting Pagination Records 33
- Using the Pagination Widget 34
- Customizing the Dashboard 35
- Available Widgets 36
- Table 6 Available Widgets 37
- Widget Description 37
- Customized Search 38
- AMP Setup > General 39
- General Settings 40
- Firmware Upgrade Defaults 45
- AirWave User Roles 49
- User Roles and VisualRF 50
- Creating AirWave User Roles 50
- Creating AirWave Users 53
- Authentication 55
- Setting up Single Sign-On 56
- Setting Up Device Types 67
- Introduction to Cisco WLSE 68
- Initial WLSE Configuration 68
- Adding an ACS Server for WLSE 69
- Discovering Devices 69
- Managing Devices 70
- Inventory Reporting 70
- Defining Access 70
- Grouping 70
- WDS Participation 70
- Primary or Secondary WDS 71
- Configuring ACS Servers 73
- PCI Auditing 75
- Requirement Description 76
- Deploying WMS Offload 77
- Setup > General page 78
- Chapter 4 79
- AirWave Groups Overview 80
- Basic section 83
- Cisco WLC Group Configuration 100
- Priority Order 106
- Wireless Protection Policies 106
- Web Auth 106
- Setting Default Description 107
- Comparing Device Groups 110
- Deleting a Group 111
- Modifying Multiple Devices 113
- Action Description 115
- Groups > Basic 117
- Master Console. For more 117
- Chapter 5 119
- SNMP/HTTP Scanning 120
- Defining a Scan Set 121
- Running a Scan Set 122
- Column Description 123
- Adding Universal Devices 125
- Figure 78 Sample CSV File 128
- Unignoring a Device 129
- Monitoring Devices 130
- AMP Alerts 131
- IDS Events 131
- Field Description 133
- Graph Description 137
- Graph Title Description 140
- Recent ARM Events Log 141
- Active BSSIDs Table 143
- Figure 96 144
- Auditing Device Configuration 148
- Configuring AP Settings 149
- Configuring AP Settings 151
- H-REAP 153
- Monitor 153
- Rogue Detector 153
- Sniffer 153
- Receive Antenna above 154
- Field Default Description 156
- Figure 110 158
- Message Meaning 161
- Chapter 6 167
- Viewing and Adding Templates 168
- Setting Description 169
- Configuring General Templates 171
- Using Template Syntax 173
- Variable Values Meaning 174
- Using AP-Specific Variables 175
- Applying Startup-config Files 178
- WDS Settings in Templates 178
- ip scp server enable 179
- Configuring a Global Template 182
- Group Name, ssid_1 184
- Subscriber 1, Value 0 184
- Chapter 7 185
- Setting Up RAPIDS 187
- Rogue Containment Options 189
- Defining RAPIDS Rules 190
- Device OUI Score 191
- Rogue Device Threat Level 192
- Option Description 193
- Recommended RAPIDS Rules 194
- Viewing Ignored Rogue Devices 198
- Score Override 199
- Using the Audit Log 200
- Additional Resources 200
- Chapter 8 201
- Log Description 203
- Table 108 Event Log Fields 204
- Viewing Triggers 205
- Creating New Triggers 205
- Setting Triggers for Devices 208
- Option Description 208
- Delivering Triggered Alerts 212
- Viewing Alerts 212
- Responding to Alerts 213
- Overview of the Clients Pages 214
- Overview of SOTI MobiControl 226
- Section Description 229
- Backing Up AirWave 241
- Running Backup on Demand 242
- Restoring from a Backup 242
- Main Tab Description Subtabs 243
- Logging out of AirWave 244
- Chapter 9 245
- Using Daily Reports 248
- Using Custom Reports 249
- Using the Dell License Report 250
- Using the IDS Events Report 256
- Using the Inventory Report 257
- Using the New Users Report 262
- Using the Port Usage Report 263
- List of most used switches 264
- List of most used ports 264
- Using the RF Health Report 265
- Defining Reports 269
- Emailing Reports to Smarthost 273
- Chapter 10 275
- Features 276
- Useful Terms 276
- Starting VisualRF 277
- Basic QuickView Navigation 277
- Network View Navigation 278
- Display Menu 279
- Figure 198 279
- Edit Menu 280
- Figure 199 280
- Operation Description 280
- Mesh View Navigation 281
- Server Settings 283
- Location Settings 284
- Attenuation Settings 286
- VisualRF Resource Utilization 287
- Increasing Location Accuracy 291
- Adding Exterior Walls 292
- Adding Client Surveys 293
- Adding Regions 294
- Adding a Wiring Closet 295
- Configuring Infrastructure 298
- Tracking Location History 301
- Planning and Provisioning 304
- Creating a New Campus 305
- Importing a Floor Plan 307
- Editing a Floor Plan Image 308
- Tweaking a Planning Region 313
- Auto-Matching Planned Devices 314
- Exporting a campus 315
- Importing from CAD 315
- Batch Importing CAD Files 316
- Common Importation Problems 317
- Pre-Conversion Checklist 317
- VisualRF Location APIs 318
- About VisualRF Plan 319
- Installation 320
- Appendix A 321
- The Shared Secret Key 323
- Enabling the IAP Role 325
- Verifying the Shared Secret 325
- Resolving Mismatches 326
- Figure 248 Audit page 327
- Other Available Features 329
- Numerics 331
Related products and manuals for Software Dell PowerConnect W-Airwave 7.5
Software Dell Vizioncore User's Guide
(23 pages)
(23 pages)
Software Dell Computer Drive CMC 3.2 User Manual
(292 pages)
(292 pages)
Software Dell Force10 Z9000 User Manual
(937 pages)
(937 pages)
Software Dell Vizioncore User Manual
(141 pages)
(141 pages)
Software Dell Brocade 6505 User's Guide
(116 pages)
(116 pages)
Software Dell Brocade 300 User's Guide
(666 pages)
(666 pages)
Software Dell Compellent Series 40 User Manual
(448 pages)
(448 pages)
Software Dell v1.1 User Manual
(175 pages)
(175 pages)
Software Dell Force10 S4810P User's Guide
(175 pages)
(175 pages)
© 2020, manymanuals.com. All rights reserved. | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals