Dell PowerVault 124T User Manual Page 57
- Page / 65
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
l Power cycle the autoloader through the front panel.
l Run the Random Moves test from either the Remote Management Unit (RMU) or the Operator Control
Panel (OCP).
Note: The Random Moves test requires a minimum of two cartridges present within the autoloader.
l If the source is a slot within a magazine, check if the spring loaded cartridge present flag moves freely
when the cartridge is manually inserted into the magazine.
l If all previous steps fail, see Contacting Dell.
AA
Picker Cartridge Sensor Error
AB
Drive Path Sensor Error
l Power cycle the autoloader through the front panel.
l Run the Random Moves test from either the Remote Management Unit (RMU) or the Operator Control
Panel (OCP).
Note: The Random Moves test requires a minimum of two cartridges present within the autoloader.
l If all previous steps fail, see Contacting Dell.
AC
Mail Slot Door Sensor Error
l Power cycle the autoloader.
l Insert a cartridge into the autoloader through the mail slot. Verify the cartridge is sensed and the
door closes fully.
l If all previous steps fail, see Contacting Dell.
AD
Mail Slot Solenoid Error
AE
Servo Initialization Error
l Remove and inspect the magazines one at a time. Turn the white thumbwheels on each magazine
and insure that the carriers move freely at least one full rotation in each direction. Re-insert each
magazine after inspection.
l Check the barcode reader setting through either the Remote Management Unit or the Operator
Control Panel.
l If the barcode reader is enabled, verify that all cartridges have valid barcode labels. If cartridges do
not have valid barcode labels, disable the barcode reader.
l Check support.dell.com for PowerVault 124T firmware updates.
l Power cycle the autoloader.
l Run the Random Moves test from either the Remote Management Unit (RMU) or the Operator Control
Panel (OCP).
Note: The Random Moves test requires a minimum of two cartridges present within the autoloader.
l If all previous steps fail, see Contacting Dell.
AF
Error Log Information Event
Used to analyze start of servo/motor error sequence in the Soft Error Log. Error entries immediately
following indicate nature of specific motor/position error.
l No action required.
Servo Picker Hardware Error Types
B0
Rotation Sensor Bad
l Power cycle the autoloader.
l Run the Random Moves test from either the Remote Management Unit (RMU) or the Operator Control
Panel (OCP).
Note: The Random Moves test requires a minimum of two cartridges present within the autoloader.
l If all previous steps fail, see Contacting Dell.
B1
Rotation Flag Not Found
B2
Rotation Flag Bad
B3
Translation Sensor Bad
B4
Translation Sensor 1 Bad
B5
Translation Sensor 2 Bad
B6
Translation Flag Bad
B7
Rotational Calibration Lost
B8
Translation Calibration Lost
B9
Rotation Lost
BA
Translation Lost
BB
Rotation Position Lost
BC
Translation Position Lost
BD
Picker Dropped Cartridge Error
l Check for a jammed cartridge in the picker. Remove the cartridge if present.
l Remove and inspect the magazines one at a time. Turn the white thumbwheels on each magazine
and insure that the carriers move freely at least one full rotation in each direction.
l Fully insert a cartridge into each magazine slot, then remove. Look for difficulty in extracting the
cartridge from each slot.
l Re-insert the magazine after inspection.
BE
Picker Missed Cartridge Error
- Notes, Notices, and Cautions 1
- User's Guide 2
- Setting Ethernet 3
- Setting the Subnet Mask 4
- Setting an IP Gateway 4
- Setting the SNMP Server 4
- Setting the Time 5
- Barcode Reader 6
- SCSI Barcode Length 6
- Setting Magazines 6
- Setting Security 6
- Setting Passwords 7
- Setting the Security 18
- Stopping a Diagnostic Test 18
- Front Panel Diagnostic Tests 18
- RMU Diagnostic Tests 19
- Technical Assistance 20
- AutoTech Service 21
- Product Information 22
- Problems With Your Order 22
- Before You Call 23
- Installation Overview 24
- Installation Preparation 24
- Host Bus Requirements 24
- Accessories 24
- Choosing a Location 24
- UL Requirements 25
- Bar Code Reader 25
- Product Overview 25
- Unpacking the Autoloader 26
- Overview 30
- Enter Passwords 31
- Using Cartridges 32
- Ejecting a Single Cartridge 33
- Ejecting a Magazine 34
- Installing a Magazine 34
- Running an Inventory 36
- Viewing Status Information 36
- Viewing Element Status 37
- Viewing Tape Drive Status 37
- Viewing Tape Drive Version 37
- Viewing Ethernet Information 37
- Configuration Page 40
- Compression 41
- Cleaning Tape 41
- Setting the Magazines 41
- Setting the System Time 42
- Setting Network Options 42
- Firmware Page 44
- Library Operations Page 45
- Back to Contents Page 46
- Physical Specifications 47
- Tape Drive Specifications 48
- Checking for Errors 51
- Autoloader Logs 52
- TapeAlert Logs 60
- Packing the Autoloader 65
Related products and manuals for Computer hardware Dell PowerVault 124T
(46 pages)
(138 pages)© 2020, manymanuals.com. All rights reserved. | 5.127 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals