Dell PowerConnect W-Airwave 8.0 User Manual

Dell NetworkingW-AirWave 8.0User Guide

10 | Contents Dell Networking W-AirWave 8.0 | User GuideDefining Floor Plan Boundaries 344Legacy VisualRF Floor Plan Configuration Options 344Defining

9. Locate the RADIUS Accounting Servers area on the Groups > SSIDs configuration page and define the settings.Table 61 describes the settings and d

101 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User GuideFigure 45:Groups > Radio Page Illustration3. Locate the Radio

Setting Default DescriptionRTS/CTS MaximumRetries (1-255)32If RTS/CTS is enabled, this specifies the maximum number of times the APissues an RTS befor

103 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User GuideSetting Default DescriptionInterferenceRobustnessNoIf enabled, thi

Setting Default DescriptionRogue Scanning YesIf enabled, Symbol access points with 3.9.2 or later firmware in the group willpassively scan for rogue a

105 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User GuideFigure 47:Groups > Cisco WLC Config Page Illustration, expande

Figure 49:Add New SSID/VLAN > General Tab IllustrationFigure 50:Add New SSID/VLAN > Security Tab IllustrationDell Networking W-AirWave 8.0 | U

107 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User GuideFigure 51:Add New SSID/VLAN > QoS Tab IllustrationFigure 52:A

Defining and Configuring LWAPP AP Groups for Cisco DevicesThe Groups > Cisco WLC Config > WLANs > Advanced > AP Groups page allows you to

109 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User Guidesettings.Go to the Groups > Cisco WLC Config > Controller pa

VisualRF Plan Installation 369Differences between VisualRF and VisualRF Plan 369Index 371Dell Networking W-AirWave 8.0 | User Guide Contents | 11

l Wireless Protection Policiesl Web AuthFigure 56 illustrates these components and this navigation:Figure 56:Groups > Cisco WLC Config > Securi

111 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User GuideFigure 58:Groups > PTMP Page Illustration3. Define the setting

Figure 59:Groups > Proxim Mesh Page IllustrationThe General section contains settings for mesh radio, number of mesh links, RSSI smoothing, roamin

113 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User GuideSetting Default DescriptionHop Factor (1-10)5Sets the factor assoc

3. Select Save when configurations are complete to retain these settings. Select Save and Apply to make the changespermanent, or select Revert to disc

115 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User Guide2. For each device type in the group, specify the minimum acceptab

Figure 62:Comparing Two Devices Groups on the Groups > List > Compare Page (Partial View)3. Note the following factors when using the Compare p

117 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User Guide3. Ensure that there are no devices in the group that you want to

l Scheduling Options — Schedules the changes to be applied to this group in the future. Enter the desired changedate in the Start Date/Time field. You

119 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User Guide4. Click the Change Device Group/Folder drop-down menu and select

12 | Contents Dell Networking W-AirWave 8.0 | User Guide

Action DescriptionAdd MaintenanceWindowAutomate the manual action of putting the selected devices into Manage mode atonce so that changes can be appli

121 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User Guidel To have Global Group status, a group must contain no devices; ac

Figure 67:Groups > Basic > Managed Page Illustrationl Once the configuration is pushed, the unchecked fields from the Global Group appears on t

123 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User Guide

Dell Networking W-AirWave 8.0 | User Guide Discovering, Adding, and Managing Devices | 124Chapter 4Discovering, Adding, and Managing DevicesThis secti

125 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User GuideSNMP/HTTP scanning information is provided in these sections

2. To create a new scan credential, select the Add button to add a new scan credential. Figure 69 illustrates this page.(Note that you may have to scr

127 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User Guide4. In the Automatic Authorization section, select whether to

Column DescriptionTotal DevicesFoundDisplays the total number of APs detected during the scan that AirWave can configure andmonitor. Total includes bo

129 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User GuideThe Cisco Discovery Protocol (CDP)CDP uses the polling inter

Dell Networking W-AirWave 8.0 | User Guide Introduction | 13Chapter 1IntroductionThank you for choosing Dell Networking W-AirWave 8.0.AirWave makes i

l "Adding Multiple Devices from a CSV File" on page 133l "Adding Universal Devices" on page 134Adding Devices with the Device Setu

131 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User GuideFigure 73:Device Setup > Add > Device Communications

Setting Default DescriptionSSH Port 22 For devices that support SSH, specify the SSH port number.CommunityString(Confirm)Taken from Device Setup >C

133 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User Guide5. At the bottom of the page, select either the Monitor Only

Figure 74:Device Setup > Add > Import Devices via CSV Page Illustration3. Select a group and folder into which to import the list of devices.4.

135 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User Guideit off the ignored list, it returns immediately to the locat

2. To change the device parameters for a given device, select its checkbox and adjust group, folder, monitor, andmanage settings as desired.3. Select

137 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User GuideVerify that the devices you added are now appearing in the A

clients, you would need to create one filter with the parameters Clients > 0, and a second filter with the parametersClients < 5.7. Drag and Dro

139 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User GuideFigure 80:Monitoring Page Bottom Level Data Common to All D

14 | Introduction Dell Networking W-AirWave 8.0 | User Guiden Configuration of APs & controllersn Automated compliance auditsn Firmware distributi

Figure 81:APs/Devices > Monitor Page for Wireless Devices (partial view of an AP)Table 74 describes the fields and information displayed in the De

141 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User GuideField DescriptionConfigurationl Good means all the settings

Field DescriptionIP AddressDisplays the IP address that AirWave uses to communicate to the device. This number is alsoa link to the AP web interface.

143 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User GuideField DescriptionChannel Width*The bandwidth of the channel

Figure 82:Interactive graphs for a DellcontrollerTable 77 describes the graphs on this page.Graph DescriptionClientsFormerly Users. Shows the max and

145 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User GuideField DescriptionDevice TypeThe type of device the user is u

Field DescriptionLAN IPAddressesDisplays the IP assigned to the user MAC. This information is not always available. AirWavecan gather it from the ARP

147 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User GuideComplete ARM statistics from Dell Networking W-Series contro

Figure 86:802.11 Radio Counters Summary tableThe frame- per-second rate of these and other 802.11 errors over time are tracked and compared in the 80

149 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User GuideGraph Title DescriptionUtilization (DellNetworking Wand Cisc

l Up-to-date heat maps and channel maps for RF diagnosticsn Adjusts for building materialsn Supports multiple antenna typesl Floor plan, building, and

Column DescriptionTime The time of the ARM event.Trap TypeThe type of trap that delivered the change information. Current ARM trap types thatdisplay i

151 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User Guidel Bluetoothl Cordless Base Freq Hopperl Cordless Phone Fixed

Figure 91:APs/Devices > Monitor page for a Mesh DeviceThese fields are described in detail in "Viewing Device Monitoring Statistics" on

153 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User GuideFigure 92:APs/Devices > Monitor Page for a Mobility Acce

The Interfaces page includes a summary of all the interfaces at the top. In case of the stacked switches, the masterincludes the interfaces of all the

155 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User GuideFigure 95:Individual Interface Information SectionBandwidth

Figure 96:APs/Devices > Audit Page Illustration6. Review the list of changes to be applied to the device to determine whether the changes are appr

157 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User Guide3. Select the Parent folder.4. Select Add.Once a new folder

Figure 98:APs/Devices > Manage > General Section Illustration3. Select Manage Read/Write on the Management Mode field.4. Select Save and Apply,

159 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User GuideFigure 99:APs/Devices > Manage Page Illustration (partia

16 | Introduction Dell Networking W-AirWave 8.0 | User Guidedevices on local networks, remote networks, and networks using Network Address Translation

Field DescriptionGroup Links to the Group > Monitoring page for the AP.TemplateDisplays the name of the group template currently configuring the AP

161 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User GuideSetting Default Device Type DescriptionRADIUS Server None In

4. Complete additional settings on the APs/Devices > Manage page, to include H-REAP, certificates, radio settings,and network settings. Table 85 de

163 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User GuideSetting Default Device Type DescriptionTransmit PowerReducti

Setting Default Device Type DescriptionSubnet Mask None AllProvides the IP subnet mask to identify the sub-network sothe IP address can be recognized

165 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User GuideField Default DescriptionPort None The port on the controlle

4. Enter a name for the maintenance window.5. In the Occurs field, specify whether the maintenance window should occur one time, or daily, weekly, mon

167 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User GuideFigure 102:Import Interfaces for Refresh and Reload (lower

Figure 103:Physical Interfaces Monitoring and Configuration SectionsFigure 104:Virtual Individual Interfaces Configuration SectionTo configure inter

169 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User GuideFigure 105:Edit Multiple InterfacesYou will remain on the s

Dell Networking W-AirWave 8.0 | User Guide Configuring AirWave | 17Chapter 2Configuring AirWaveThis section contains the following procedures to deplo

Figure 107:APs/Devices > Manage > Device CommunicationThe Device Communication area may appear slightly different depending on the particular v

171 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User Guidemonitor-only mode in AMP Setup > General or 2) if you are

Figure 108:APs/Devices > Manage Firmware UpgradesInitiating a firmware upgrade will change the Firmware Status column for the device to Pending in

173 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User GuideMessage MeaningAP is no longerassociated withcontrollerThis

Figure 109:View Device Credentials WindowThe View Device Credentials message may appear slightly different depending on the vendor and model.5. If th

175 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User Guidel Dell Networking W AP Groups running permanently with the d

The above steps will use the defaults in the referenced Spectrum Profile. In most cases, you should not change thesettings in the default profile. If

177 | Discovering, Adding, and Managing Devices Dell Networking W-AirWave 8.0 | User GuideTo disable Spectrum mode on this individual AP after it has

Dell Networking W-AirWave 8.0 | User Guide Creating and Using Templates | 178Chapter 5Creating and Using TemplatesThis section provides an overview an

179 | Creating and Using Templates Dell Networking W-AirWave 8.0 | User GuideTemplate VariablesVariables in templates configure device-specific proper

18 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideFigure 1:Navigation Bar Displaying Down Device StatisticsYou can control the Top H

l %password%l %power%l %radius_server_ip%l %rf_band%l %server_cert_checkstum%l %syslocation%l %syslog_server%The variable settings correspond to devic

181 | Creating and Using Templates Dell Networking W-AirWave 8.0 | User GuideSetting DescriptionDevice TypeDisplays the template that applies to APs o

Setting Default DescriptionUse Global Template NoUses a global template that has been previously configured on theGroups > Templates configuration

183 | Creating and Using Templates Dell Networking W-AirWave 8.0 | User GuideSetting Default DescriptionTelnet/SSHUsernameNoneIf the template is updat

2. Select an AP from the Group to serve as a model AP for the others in the Group. You should select a device that isconfigured currently with all the

185 | Creating and Using Templates Dell Networking W-AirWave 8.0 | User Guideactual logging facility local6actual logging queue-limit 100actual loggin

config file as "configuration mismatches.” Lines enclosed in <push_and_exclude> are included in the AP startup-configfile but AirWave ignor

187 | Creating and Using Templates Dell Networking W-AirWave 8.0 | User GuideVariable Values MeaninginterfaceDot11Radio0 2.4GHz radio module is instal

Variable Meaning Command Suppressed Defaultantenna_ receive Receive antennaantenna receive %antenna_receive%diversityantenna_transmit Transmit antenna

189 | Creating and Using Templates Dell Networking W-AirWave 8.0 | User Guideorganization %organization%%endif%syslog-server 216.31.249.235syslog-leve

Customizing Columns in ListsCustomize the columns for any list table selecting Choose Columns, as shown in the figure below. Use the up/downarrows to

service avt%avt_ingress_interface%%avt_ingress_ip%buffer_time 200mode %avt_mode%AirWave displays a warning if AirMesh APs attempting to either upgrade

191 | Creating and Using Templates Dell Networking W-AirWave 8.0 | User Guideaaa group server radius wds server10.2.25.162 auth-port 1645 acct-port 16

%IF interface=Dot11Radio1%interface Dot11Radio1bridge-group 1bridge-group 1 block-unknown-sourcebridge-group 1 spanning-disabledbridge-group 1 subscri

193 | Creating and Using Templates Dell Networking W-AirWave 8.0 | User Guide!username admin password 1 5baa61e4c9b93f3f0682250b6cf8331b7ee68fd8userna

radio %radio_index% rts-threshold 2345radio %radio_index% max-mobile-units 25radio %radio_index% admission-control voice max-perc 76radio %radio_index

195 | Creating and Using Templates Dell Networking W-AirWave 8.0 | User GuideFigure 115:Group > Templates > Add Page Illustration4. Use the dro

n Group Name—the name of the subscriber group that you wish to update.n Variable Name—the name of the group template variable you wish to update.n Var

197 | Creating and Using Templates Dell Networking W-AirWave 8.0 | User Guide

Dell Networking W-AirWave 8.0 | User Guide Using RAPIDS and Rogue Classification | 198Chapter 6Using RAPIDS and Rogue ClassificationThis chapter provi

199 | Using RAPIDS and Rogue Classification Dell Networking W-AirWave 8.0 | User GuideFigure 117:RAPIDS > Overview Page Illustration (partial view

June 2014 | 0510897-18 Dell Networking W-AirWave 8.0 | User GuideCopyright© 2014 Aruba Networks, Inc. Aruba Networks trademarks include , Aruba Networ

20 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideFigure 4:Table with Choose Columns for Roles Menu SelectedResetting Pagination Rec

Summary DescriptionAcknowledgedRAPIDS DevicesA color coded pie chart comparing the number of acknowledged devices to theunacknowledged devices.RAPIDS

201 | Using RAPIDS and Rogue Classification Dell Networking W-AirWave 8.0 | User GuideField Default DescriptionARP IP Match Timeout (1-168 hours)24If

Field Default DescriptionManage rogue APcontainmentNoSpecifies whether RAPIDS will manage the classification of rogue APson Cisco WLCand Dell control

203 | Using RAPIDS and Rogue Classification Dell Networking W-AirWave 8.0 | User Guidel Use the AMP Setup > General > Performance Tuning page to

Device OUI ScoreThe Organizationally Unique Identifier (OUI) score is based on the LAN MAC address of a device. RAPIDS can beconfigured to poll your r

205 | Using RAPIDS and Rogue Classification Dell Networking W-AirWave 8.0 | User GuideFigure 119:RAPIDS > Rules Page IllustrationTable 101 defines

Figure 120:Classification Rule PageFill in the settings described in Table 101 then select an option from the drop down menu.Table 102 defines the dr

207 | Using RAPIDS and Rogue Classification Dell Networking W-AirWave 8.0 | User GuideOption DescriptionWireline PropertiesDetected on LAN Rogue is de

This means that user’s laptops on your network may appear as Ad-Hoc devices that are broadcasting your SSID. Ifthis happens too frequently, you can re

209 | Using RAPIDS and Rogue Classification Dell Networking W-AirWave 8.0 | User GuideColumn DescriptionAckDisplays whether or not the rogue device ha

Using the Pagination WidgetThe pagination widget is located at the top and bottom of every list table, as shown in Figure 7.Figure 7:Pagination Widge

Column DescriptionRSSIDisplays Received Signal Strength Indication (RSSI) designation, a measure of the powerpresent in a received radio signal.Networ

211 | Using RAPIDS and Rogue Classification Dell Networking W-AirWave 8.0 | User GuideColumn DescriptionCurrentAssociationsThe number of current rogue

l You can use the global filtering options on the RAPIDS > Setup page to filter rogue devices according to signalstrength, ad-hoc status, and disco

213 | Using RAPIDS and Rogue Classification Dell Networking W-AirWave 8.0 | User GuideOnce a new score is assigned, all devices with the specified MAC

5. To remove any override, select that override in the check box, and then click the Delete button.Using the Audit LogThe Audit Log is a record of any

215 | Using RAPIDS and Rogue Classification Dell Networking W-AirWave 8.0 | User Guide

Dell Networking W-AirWave 8.0 | User Guide Performing Daily Administration in AirWave | 216Chapter 7Performing Daily Administration in AirWaveDaily WL

217 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideSystem Page Description Refer toFirmware UpgradeJobsDisplay

The link diagnostics.tar.gz contains reports and logs that are helpful to Dell support in troubleshooting and solvingproblems. Your Dell support repre

219 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideTable 107 describes the columns and the information provide

22 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideFigure 9:Interactive Graphs on the Home > Overview PageHighcharts are built wit

Column DescriptionTime Date and time of the event.User The AirWave user that triggered the event. When AirWave itself is responsible, System is displa

221 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideFigure 129:Add New Trigger Page Illustration2. In the Trig

Figure 130:System > Triggers > Add Trigger Type Drop Down MenuThe Add Trigger page changes depending on the trigger type that you select. In ma

223 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User Guideb. The Alert Notifications settings section allows you to e

Trigger Option DescriptionDevice UpThis trigger type activates when an authorized, previously down AP is now responding toSNMP queries. To set the con

225 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideRadio Trigger Options DescriptionRadio DownIndicates that a

1. Choose a trigger type from the Clients category, listed in the Type drop-down menu. See Figure 130 in "CreatingNew Triggers" on page 220.

227 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User Guide2. Repeat this procedure for as many triggers and condition

Setting Triggers for AirWave HealthAfter completing steps 1-3 in "Creating New Triggers" on page 220, perform the following steps to configu

229 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideThis table displays alerts as follows; select the alert Typ

The Customize workspace that appears is shown in Figure 11.Figure 11:Customize Overview PageAdding WidgetsThe Home > Overview page displays the cu

Figure 134:System > Triggers Page Illustration (partial view)Refer to "Creating New Triggers" on page 220 for additional information.Del

231 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User Guidel Leave it in active status if it is unresolved. The alert

A file transfer client that supports SFTP/SCP for Windows is WinSCP: http://winscp.sourceforge.net/eng/WinSCP allows you to transfer the nightly00[1-4

233 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideSuccessful upgrade jobs are not archived on this page -- ge

l Database Statisticsl Disk SpaceFigure 139 illustrates this page, and Table 118 describes fields and information displayed.Figure 139:System > Pe

235 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideField DescriptionSystem Memory UsageThe amount of RAM that

Field DescriptionHigh Performance SNMPFetcher RequestsThe number of SNMP get and walk requests per second performed by the highperformance SNMP (v2c)

237 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User Guidel "Monitoring WLAN Users in the Clients > Connected

Clients Page Description Refer ToDiagnosticsDisplays possible client device issues, diagnostic summary data,user counts, AP information, 802.11 counte

239 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideFigure 141:Center paneThe right pane provides information

24 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideWidget DescriptionClient/Usage GraphsThe Client graph is enabled by default and, by

l The Folder field shows the current folder of Connected Clients you are viewing. You can view users under aparticular folder from the Go to folder dr

241 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideFigure 143:Clients > Connected Page Illustration (Parti

Field DescriptionDevice Type The type of device determined by AMP Setup > Device Type Setup rules.Duration The length of time the MAC address has b

243 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideField DescriptionSerialNumberSerial number of the device.Se

Field DescriptionMAC AddressDisplays the MAC address of the rogue client. Click on this to jump to the Clients > ClientDetail page for this rogue.U

245 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideFigure 145:AMP Setup > Users Page Illustration3. The ne

Field DescriptionRepair Guest UserErrorsSets AirWave to attempt to push the guest user again in an attempt to repair any errors inthe Status column.Ad

247 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideFigure 147:Clients > Guest Users > Add New Guest Use

Figure 148:Clients > VPN Sessions Page IllustrationWhen a VPN username is selected, a Clients > VPN User Detail page displays with current VPN

249 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideField DescriptionName Displays the user-editable name assoc

Widget DescriptionRAPIDS: ClassificationSummaryThe RAPIDS: Classification Summary table shows the number of devicesclassified as Valid, Suspected Vali

Figure 150:Clients > Client Detail page illustration (partial view)Mobile Device Access Control in Clients > Client Detail and Clients > Con

251 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideFigure 151:Device Info section in Clients > Client Deta

Controllers show several more pages in this menu (Security Dashboard, for instance) if the controller is runningArubaOS version 6.1 or greater.l Run a

253 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideViewing the Rogue Association History for a ClientPast asso

Managing Mobile Devices with SOTI MobiControl and AirWaveOverview of SOTI MobiControlSOTI MobiControl, the mobile device management platform for Windo

255 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideThe list page for the MDM server also displays:l Last Conta

Home Page Description Refer toRF CapacityThis page provides admin users with a summary of network usage over aone-week period. This information includ

257 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideFigure 157:Home > Overview Page IllustrationSection Des

Section DescriptionAlert SummaryThis section displays all known and current alerts configured and enabled in the System >Alerts page (refer to &quo

259 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideThe Home > AppRF pages may show IP addresses rather than

26 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideWidget DescriptionTop Folders By A Radio ClientCountThis chart shows the folders an

Call QualityThis pane provides information about the quality of calls on the network over the selected time period. Select the type ofcall quality inf

261 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideBy default, the data in this table is displayed by the call

Figure 161:Drill down to view all clientsWhen the client information is displayed, an additional drill down is available to view information for a sp

263 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideFigure 162:The Home > RF Capacity pageYou can click on

Figure 164:Example popup showing channel utilizationViewing the Home > Network Deviations PageThe Home > Network Deviations page provides graph

265 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideFigure 165:Home > Network Deviations pageThe first time

2 +- 5Normal Range: 3 - 7SD(2):-------2*SD +- Mean2*2 +- 54 +- 5Normal Range: 1 - 9SD(3):-------3*SD +- Mean3*2 +- 56 +- 5Normal Range: 0 - 11 (-1 is

267 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideFigure 167:Home > Search Page Illustration with Sample

Figure 168:Home > License Page IllustrationField DescriptionOrganization Displays the organization listed on your license key.Product This product

269 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideConfiguring Your Own User Information with the Home > Us

This search type will be used when a user types an entry in the Search field and then clicks Enter without selecting aspecific search type.l Use Syste

Field DescriptionCustomize Header ColumnsEnables/disables the ability to control which statistics hyperlinks (also knownas Top Header Stats) are displ

271 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideField DescriptionCustomize Columns for OtherRolesAllows adm

Figure 170:Master Console Home > Overview Page Illustrationl Reports can be run from the Master Console to display information from multiple AirWa

273 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideFigure 171:Public Portal Page IllustrationThe Public Porta

Using Global Groups with Master ConsoleTo push configurations to managed groups using the AirWave Global Groups feature, follow these steps:1. Navigat

275 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User GuideUsing AirWave Failover for BackupThe failover version of Ai

Setting Default DescriptionIP/Hostname NoneThe IP address or Hostname of the watched AMP.The Failover AMP needs HTTPS access to the watched AMPs.Usern

277 | Performing Daily Administration in AirWave Dell Networking W-AirWave 8.0 | User Guide

Dell Networking W-AirWave 8.0 | User Guide Creating, Running, and Emailing Reports | 278Chapter 8Creating, Running, and Emailing ReportsThis section d

279 | Creating, Running, and Emailing Reports Dell Networking W-AirWave 8.0 | User GuideEach pane includes a Latest Report column with the most recent

28 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideFigure 13:Home > User Info > Severe Alert Threshold Drop Down MenuDefining G

Figure 172:Reports > Definitions Page IllustrationFigure 173:Report Type Drop down Menu in Reports > Definitions IllustrationOnly admin users

281 | Creating, Running, and Emailing Reports Dell Networking W-AirWave 8.0 | User Guidel The latest daily reports for immediate online viewingYou can

1. To create or edit a report, browse to the Reports > Definition page and click the Add button, or select the pencilicon to edit an existing repor

283 | Creating, Running, and Emailing Reports Dell Networking W-AirWave 8.0 | User GuideField Default DescriptionGroup All GroupsSpecify the groups an

Field Default DescriptionSchedule NoWhen you select Yes, new fields display that allow you to define a specific time forreport creation. The report sc

285 | Creating, Running, and Emailing Reports Dell Networking W-AirWave 8.0 | User GuideFigure 177:Report Restrictions IllustrationBy default all dat

Report TypeCan by Runby TimePeriodCan be Run byGroup/FolderDescription"Using CustomReports" on page288Yes YesSummarizes devices based on whi

287 | Creating, Running, and Emailing Reports Dell Networking W-AirWave 8.0 | User GuideReport TypeCan by Runby TimePeriodCan be Run byGroup/FolderDes

Viewing Generated ReportsThe Reports > Generated page supports the following general viewing options:l By default, the reports on the Reports >

289 | Creating, Running, and Emailing Reports Dell Networking W-AirWave 8.0 | User GuideFigure 178:Custom Options Page IllustrationThe left pane of t

Refer to the following sections for information about the available settings:l "General Settings" on page 29l "Automatic Authorization

Figure 179:Dell Networking W Detail PageUsing the Capacity Planning ReportThe Capacity Planning Report tracks device bandwidth capacity and throughpu

291 | Creating, Running, and Emailing Reports Dell Networking W-AirWave 8.0 | User GuideFigure 180:Capacity Planning Report Detail Page (partial view

Using the Client Inventory ReportThe Client Inventory Report can be used for viewing information about clients that have connected to you network.Simi

293 | Creating, Running, and Emailing Reports Dell Networking W-AirWave 8.0 | User Guidel Last Connection Mode Summaryl Last SSIDSummary5. Specify &q

Field DescriptionCount Shows the total number of each device current included in the client inventory.% of TotalShows the percentage of each of those

295 | Creating, Running, and Emailing Reports Dell Networking W-AirWave 8.0 | User GuideFinally, you can specify the details that you want to include

Field DescriptionTotal traffic Out (MB) The total amount of traffic that passed out of the network.Avg traffic per session(MB)The average amount of tr

297 | Creating, Running, and Emailing Reports Dell Networking W-AirWave 8.0 | User GuideFigure 183:Daily Configuration Audit Report Page, partial vie

l Least Utilized by Bandwidth—By default, this list displays the 10 devices that are the least used, according to thebandwidth throughput.l Devices—Th

299 | Creating, Running, and Emailing Reports Dell Networking W-AirWave 8.0 | User GuideField DescriptionAverage UsageDisplays the average rate of dat

Dell Networking W-AirWave 8.0 | User Guide Contents | 3ContentsIntroduction 13A Unified Wireless Network Command Center 13AirWave Management Platform

30 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideSetting Default DescriptionDeviceConfigurationAudit IntervalDailyThis setting defin

Figure 185:Device Uptime Report IllustrationField DescriptionSNMP UptimeDisplays the percentage of time the device was reachable via ICMP. AirWave po

301 | Creating, Running, and Emailing Reports Dell Networking W-AirWave 8.0 | User GuideThe Home > Overview page also cites IDS events. Triggers ca

Field DescriptionPrecedence Displays precedence information associated with the IDS event, when known.Time Displays the time of the IDS event.Table 14

303 | Creating, Running, and Emailing Reports Dell Networking W-AirWave 8.0 | User GuideFigure 187:Inventory Report Illustration (partial view)Field

Field DescriptionModel/Firmware VersionThis field further breaks down the firmware version into specific device modelsand specific versions. This incl

305 | Creating, Running, and Emailing Reports Dell Networking W-AirWave 8.0 | User GuideField DescriptionFolder/AP/ClientThe total number of matches t

Figure 189:Daily Memory and CPU Usage Report IllustrationUsing the Network Usage ReportThe Network Usage Report contains network-wide information in

307 | Creating, Running, and Emailing Reports Dell Networking W-AirWave 8.0 | User GuideFigure 190:Network Usage Report IllustrationField Description

Using the New Clients ReportThe New Clients Report lists all new users that have appeared on the network during the time duration defined for therepor

309 | Creating, Running, and Emailing Reports Dell Networking W-AirWave 8.0 | User GuideField DescriptionUsername The client name, if available.Role T

Top Header SettingsOn the AMP Setup > General page, locate the Top Header section to select the Top Header Stats to be displayed at thetop of the i

Figure 192:New Rogue Devices Report Illustration (partial view)The rogue device inventories that comprise this report contain many fields, described

311 | Creating, Running, and Emailing Reports Dell Networking W-AirWave 8.0 | User GuideField DescriptionOperating System Displays the operating syste

Figure 193:PCI Compliance Report Illustration ExampleUsing the Port Usage ReportYou can generate a wide array of port usage statistics from the Port

313 | Creating, Running, and Emailing Reports Dell Networking W-AirWave 8.0 | User GuideFigure 194:Port Usage Report Detail Page (partial view)Field

Field DescriptionContact Displays the contact info for the switch, if availableLocation Displays the location information for the switch, if available

315 | Creating, Running, and Emailing Reports Dell Networking W-AirWave 8.0 | User GuideFigure 195:RADIUS Authentication Issues detail page illustrat

Figure 196:Daily RF Health Report Page Illustration (partial view)All tables in RF Health indicate the rank, device type, number of users, bandwidth,

317 | Creating, Running, and Emailing Reports Dell Networking W-AirWave 8.0 | User GuideFigure 197:Rogue Clients Report Page IllustrationField Descri

Field DescriptionCh BW The channel bandwidth of the client, if avaialbleRadio Mode The radio mode that the rogue client is using.SNR The signal-to-noi

319 | Creating, Running, and Emailing Reports Dell Networking W-AirWave 8.0 | User Guidereport. Finally, you can specify to include summary or detaile

32 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideSetting Default DescriptionAPFully QualifiedDomain NameOptionsNoSets AirWave to use

All reports contain a link to export the report to an XML, CSV, or PDF file. Reports can also be e-mailed in eitherHTML, PDF,or CSV format.Select Ema

321 | Creating, Running, and Emailing Reports Dell Networking W-AirWave 8.0 | User GuideSupport for graphics and links is included when exporting. Thi

Dell Networking W-AirWave 8.0 | User Guide Using VisualRF | 322Chapter 9Using VisualRFThis chapter contains information about VisualRF and includes th

323 | Using VisualRF Dell Networking W-AirWave 8.0 | User GuideFeaturesl Mesh monitoring page specially for viewing Dell AirMesh devices. VisualRF aut

l Session - A session is an instance when a client connects to the network.The period of time in which the clientremains connected to the network is t

325 | Using VisualRF Dell Networking W-AirWave 8.0 | User GuideNetwork View NavigationThe Network view provides page specially for viewing campuses, b

Floorplan View NavigationWhen viewing a floor plan in the Floorplan view, the View menu displays controls to display selected Devices,Overlays, Displa

327 | Using VisualRF Dell Networking W-AirWave 8.0 | User Guidel Voice - Provides color-coded overlay based on number of radios covering each grid cel

Figure 206:Viewing Mesh Networks in VisualRFClick on an AirMesh network to display the APs with labels, as shown in Figure 207Figure 207:APs in a me

329 | Using VisualRF Dell Networking W-AirWave 8.0 | User GuideOperation Icon DescriptionPreferencesConfigure personal viewing preferences. The Prefer

Setting Default DescriptionAllow WMS Offloadconfiguration inmonitor-only modeNoWhen Yes is selected, you can enable the ArubaOS WMS offloadfeature on

Figure 209:VisualRF General preferencesThis menu allows you to configure the following settings:l Enable auto-refresh toggle. If enabled, specify the

331 | Using VisualRF Dell Networking W-AirWave 8.0 | User GuideThis menu allows you to configure the following settings:l Usage - select the kbps thre

Figure 212:VisualRF Overlays preferencesThis menu allows you to configure the following settings:l Grid - non vector overlayl Vector - provides a smo

333 | Using VisualRF Dell Networking W-AirWave 8.0 | User GuideFigure 214:VisualRF Navigation preferencesThis menu allows you to configure the follow

Figure 215:The VisualRF > Setup Page (partial view)Server SettingsTo enable VisualRF and tune memory and performance, navigate to the Server Setti

335 | Using VisualRF Dell Networking W-AirWave 8.0 | User GuideSetting Default DescriptionMemory Allocation 512 MBThe amount of memory dedicate to Vis

Setting Default DescriptionAlloweddeviation forclient placement4 dBWhen VisualRF locates a client or rogue it utilizes signal metrics from all theAPs

337 | Using VisualRF Dell Networking W-AirWave 8.0 | User GuideSetting Default DescriptionLaptop Min/Max(sec)90/360This timer determines how often to

Setting Default DescriptionPrinter Min/Max (sec) 120/480This timer determines how often to calculate the location of printers. Takenwith the data samp

339 | Using VisualRF Dell Networking W-AirWave 8.0 | User GuideSetting Default dB DescriptionConcrete Attenuation(dB)15Specifies the attenuation for a

34 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideSetting Default DescriptionSyslog Server N/AEnter the IP address of the syslog serv

Planning and ProvisioningVisualRF provides the capability to plan campuses, buildings, floors, and access points prior to the actual access pointdeplo

341 | Using VisualRF Dell Networking W-AirWave 8.0 | User GuideField DescriptionName Name of the building located in an existing campus.Address Buildi

Creating a Floor PlanThe following steps show how to import a floor plan background image file. Floor plans can be added (imported),edited, and delete

343 | Using VisualRF Dell Networking W-AirWave 8.0 | User GuideBy default the importation wizard allocates 2,500 grid cells to each site based on dime

6. Click OK.Defining Floor Plan BoundariesUse the Floorplan Boundary section of the HTML5 Floor Upload Wizard to refine the floor plan to remove white

345 | Using VisualRF Dell Networking W-AirWave 8.0 | User GuideFigure 219:Checking for CAD errorsControlling the Layers in the Uploaded Floor Plan (C

4. Click on the floor plan graphic to define the edge of the new region. Use the slider bar at the upper left corner of thewizard to zoom in to a sect

347 | Using VisualRF Dell Networking W-AirWave 8.0 | User Guide2. Right-click the floor and select Duplicate.3. Enter the following information:l Star

Figure 221:Provisioning DevicesWired devices that are added to a wired closet are included in any BOM report covering that floor.Deployed switches on

349 | Using VisualRF Dell Networking W-AirWave 8.0 | User GuideEditing a Planning RegionYou can edit a region by right-clicking within the region to s

Setting Default DescriptionAutomaticallyAcknowledge Alerts(0-550 days, zerodisables)14Defines automatically acknowledged alerts as the number of days

AirWave recalculates path loss and client locations after adding a deployed AP. All changes may not be visible on arefresh until this process complete

351 | Using VisualRF Dell Networking W-AirWave 8.0 | User Guide1. Determine if you want to plan for APs on a new floor using the Floor Upload wizard,

Figure 224:Bill of Materials Report IllustrationIncreasing Location AccuracyThe Location Service will use all RF information available to increase lo

353 | Using VisualRF Dell Networking W-AirWave 8.0 | User GuideMFG/ModelClient Signal AssociatedAPAP-to-AP Signals(DynamicAttenuation)UnassociatedClie

Figure 225:Drawing a wall4. (Optional) Change the attenuation of a wall by selecting the appropriate building material for that wall.l To define the

355 | Using VisualRF Dell Networking W-AirWave 8.0 | User Guide3. Click the Add button for Static Training, as shown in Figure 227:Figure 227:Marking

Figure 228:Timing Factors Impacting Location AccuracyThese best practices are recommended when configuring hardware infrastructure:l For legacy auton

357 | Using VisualRF Dell Networking W-AirWave 8.0 | User GuideFigure 230:Rectangular Floor Plan AP DeploymentAdding Client SurveysClient surveys wit

Figure 231:Client Surveys3. Select the Surveys and Training option.4. Select the appropriate transmit power for the wireless client. Leave the defaul

359 | Using VisualRF Dell Networking W-AirWave 8.0 | User GuideClient Type Transmit Power 11giPhone 20 mWDesktop 100 mWCisco Cards 100 mWTable 164:Aut

36 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideSetting Default DescriptionDevice Uptime (0-120 months, zerodisables)60Sets the num

Figure 234:VisualRF thumbnail in Clients > Client DetailThis view is focused on the wireless user enabling you quick resolution of a user's i

361 | Using VisualRF Dell Networking W-AirWave 8.0 | User GuideFigure 235:Show Location HistoryA location history player, illustrated in Figure 236,

Figure 238:VisualRF Thumbnail in APs/Devices > Monitor page for an APA fully interactive VisualRF display opens below the graphs on the same page

363 | Using VisualRF Dell Networking W-AirWave 8.0 | User GuideField DescriptionCampus Campus associated to the floor.Building Building associated to

Figure 240:Network List View3. Click any of the links to view that location, or click a column heading to sort the list by that column criteria. TheO

365 | Using VisualRF Dell Networking W-AirWave 8.0 | User GuideImporting and Exporting in VisualRFExporting a campusTo export a campus from VisualRF s

Pre Processing Steps1. Increase Memory Allocation in VisualRF > Setup as follows:l 25 floors or less - 512 MBl 25 to 75 floors - 1 GBl More than 75

367 | Using VisualRF Dell Networking W-AirWave 8.0 | User Guide</access-points></floor><floor name="2nd Floor" number="4

VisualRF Location APIsVisualRF provides the following location APIs:Site Inventory: https://[amp_host]/visualrf/site.xml?site_id=...l You can find the

369 | Using VisualRF Dell Networking W-AirWave 8.0 | User Guide<total-bandwidth>0</total-bandwidth><total-clients>0</total-client

Setting Default DescriptionEnable RTLSCollectorNoEnables or disables the RTLS Collector, which is used to allowArubaOScontrollers to send signed and e

Feature VisualRF VisualRF PlanTrack users XTrack interferers XVisualRF APIs XLocation accuracy XVisualRF preferences XResource utilization XAdd extern

IndexDell Networking W-AirWave 8.0 | User Guide Index | 3718802.11 counters 86, 147-148, 238AAAA Servers 79, 91Access PointsAdding with CSV File 133AC

ConfigurationAMP 17, 28WMS Offload 76Change Jobs, Viewing 159, 232Compliance chart 257Controllers 14Templates and Variables 183Whitelists 49Configurat

Configuring Security Settings 92Deleting 116Deleting a Group 116Global Groups 81, 120MAC ACLs 113Overview 80Radio Settings 100Security 92Viewing 81Gue

Ppagination recordssetting, resetting 20pagination widget, using 21PCI ComplianceDefault Credential Compliance 76PCI Requirements 74Physical Interface

SSample ResponseDevice Location 368Site Inventory 368Scan Sets 126ScanningCredentials 125Search Method 31Secondary Network Interface Settings 40Securi

Clients > Clients Detail 255Clients > Connected 239-240Clients > Diagnostics 253Clients > Guest Users 245Clients > Tags 248Clients >

QuickView 145, 324Removing Color 344Roles 43SettingsAdding a New Attenuation 339SetupAttenuation Settings 338Controller 367Location Calculation Timer

38 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideSetting Default DescriptionPrefer AMONvsSNMP PollingSNMPPollingPrefer AMON is a co

Setting Default DescriptionVerbose Loggingof SNMPConfigurationNoEnables or disables logging detailed records of SNMP configurationinformation.SNMP Rat

4 | Contents Dell Networking W-AirWave 8.0 | User GuideUser Roles and VisualRF 43Creating AirWave User Roles 43Configuring Login Message, TACACS+, RAD

40 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuidePrimary Network Interface SettingsLocate the Primary Network Interface section. The

Setting Default DescriptionPrimary ntp1.yourdomain.com Sets the IP address or DNS name for the primary NTP server.Secondary ntp2.yourdomain.com Sets t

42 | Configuring AirWave Dell Networking W-AirWave 8.0 | User Guide2. Select Add to create a new user, select the pencil icon to edit an existing user

Setting Default DescriptionEmailAddressNoneAllows you to specify a specific email address that will propagate throughout manyadditional pages in AirWa

44 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideFigure 18:AMP Setup > Roles Page Illustration2. Select Add to create a new role

Setting Default DescriptionName NoneSets the administrator-definable string that names the role. The role nameshould indicate the devices and groups t

46 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideSetting Default DescriptionTop Folder TopDefines the highest viewable folder for th

Setting Default DescriptionAllowaccounts withno expirationYesSpecifies whether to allow accounts that have no expiration set. If this is set toNo, the

48 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideSetting Default DescriptionTop Folder TopDefines the Top viewable folder for the ro

Setting Up Login Configuration OptionsOn the AMP Setup > Authentication page, administrators can optionally configure the AirWave user's idle

Cisco WLC Group Configuration 104Accessing Cisco WLC Configuration 104Navigating Cisco WLC Configuration 104Configuring WLANs for Cisco WLC Devices 10

50 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideFigure 21:Enabling AirWave WhitelistsSetting Up Certificate AuthenticationOn the A

Specifying the Authentication PriorityTo specify the authentication priority for this AirWave, locate the Authentication Priority section in AMP Setup

52 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideField Default DescriptionSecondary ServerHostname/IP AddressN/A Enter the IP addres

Figure 24:AMP Setup > RADIUS > Add RADIUS Accounting Client Page Illustration1. To specify the RADIUS authentication server or network, browse

54 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideFigure 25:AMP Setup > Authentication Page Illustration for TACACS+2. Select No

4. Select Save.5. Edit the existing groups or users in TACACS to use the AMP service and define a role for the group or user.l The role defined on the

56 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideFigure 26: AMP Setup > Authentication Page Illustration for LDAP3. Complete the

Field Default DescriptionView Server Certificate noneIf Connection Type is configured as start-tls, then also specifywhether the start-tls connection

58 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideField Default DescriptionAdd New LDAP Rule noneThe LDAP rule parameters are Positio

Figure 27:Device Setup > Communication Page IllustrationPerform the following steps to define the default credentials and SNMP settings for the wi

6 | Contents Dell Networking W-AirWave 8.0 | User GuideMonitoring Data for Wired Devices (Routers and Switches) 152Understanding the APs/Devices >

60 | Configuring AirWave Dell Networking W-AirWave 8.0 | User Guide3. Locate the SNMPv3 Informs section. Select the Add button to reveal configuration

Setting Default DescriptionDo Not ModifySNMP SettingsYesWhen selected, specifies that AirWave will not modify any SNMP settings. IfSNMP is not already

62 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideSetting Default DescriptionFirmwareVersionNoneDisplays the firmware version number.

4. Enter the appropriate information and select Add. The file uploads to AirWave and once complete, this file appearson the Device Setup > Upload F

64 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideAdditional fields may appear for multiple device types. AirWave prompts you for add

Check or uncheck the checkbox under the Enabled column to turn device setup rules on or off.Refer to "Monitoring and Supporting WLAN Clients"

66 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideSWAN Component RequirementsACS (Access ControlServer)l IP Addressl LoginAPsl APs wi

l Importing from a filel Importing from CiscoWorksPerform these steps to discover access points.1. Go to the Device > Managed Devices > Discover

68 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideWDS ParticipationPerform these steps to configure WDS participation.1. Log in to th

Figure 31:AMP Setup > WLSE > Add New WLSE Page IllustrationPerform the following steps for optional configuration of AirWave for support of Cis

Containment Options 201Filtering Options 202Additional Settings 202Defining RAPIDS Rules 203Controller Classification with WMS Offload 203Device OUI S

70 | Configuring AirWave Dell Networking W-AirWave 8.0 | User Guide2. After you have completed all fields, select Save. AirWave is now configured to g

Field Default DescriptionIP/Hostname None Sets the DNS name or the IP address of the ACS Server.Protocol HTTPLaunches a drop-down menu specifying the

72 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideFigure 34:AMP Setup >NMS Page Illustration2. Select Add to integrate a new NMS

l Complete the required configurations in this chapter before proceeding. Dell support remains available to you for anyphase of AirWave installation.A

74 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideRequirement Description1.1Monitoring configuration standards for network firewall d

Requirement Description11.4Using intrusion-detection or intrusion-prevention systems to monitor all trafficWhen Enabled: AirWave reports pass or fail

76 | Configuring AirWave Dell Networking W-AirWave 8.0 | User GuideFigure 36:Default Credential Compliance for PCI Requirements4. Select Save.5. To v

a. Disable debugging.b. Ensure the AirWave server is a trap receiver host.c. Ensure proper traps are enabled.2. Configure AirWave to optimally monitor

Dell Networking W-AirWave 8.0 | User Guide Configuring and Using Device Groups | 78Chapter 3Configuring and Using Device GroupsThis section describes

79 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User GuideMenuItemDescription Refer toAAAServersThis page configures authenti

8 | Contents Dell Networking W-AirWave 8.0 | User GuideManaging Mobile Devices with SOTI MobiControl and AirWave 254Overview of SOTI MobiControl 254Pr

MenuItemDescription Refer toFirmware This page manages firmware files for many devices."SpecifyingMinimumFirmwareVersions forAPs in aGroup"

81 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User GuideIndividual device settings—such as device name, RF channel selectio

Column DescriptionIs Global GroupIf a group is designated as global, it may not contain APs but it may be used as a template forother groups. This col

83 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User GuideFigure 39:Pop-up When Hovering over Wrench Icon in Groups > Lis

Figure 40:Groups > Basic Page Illustration1. Define the settings in the Basic and Global Group sections. Table 41 describes several typical settin

85 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User GuideSetting Default DescriptionNameDefinedwhen firstadding thegroupDisp

Setting Default DescriptionClient Data Polling Period10minutesSets time between SNMP polls for client data for devices in the group.Thin AP Discovery

87 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User GuideSetting Default DescriptionInterface Error CounterPolling Period30m

Setting Default DescriptionSubnet Mask none Sets the subnet mask to be assigned to the devices in the Group.SubnetGatewaynone Sets the gateway to be a

89 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User GuideSetting Default DescriptionSNMP Version 2c The version of SNMP used

Example 302Using the Match Event Report 304Using the Memory and CPU Utilization Report 305Using the Network Usage Report 306Using the New Clients Repo

Setting Default DescriptionIgnore RoguesDiscovered byRemote APsNoConfigures whether to turn off RAPIDS rogue classification and roguereporting for RAP

91 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User Guide17. Select Save when the configurations of the Groups > Basic co

Setting Default DescriptionSecret and ConfirmSecretNoneSets the shared secret that is used to establish communication betweenAirWave and the RADIUS se

93 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User GuideFigure 42:Groups > Security Page IllustrationSetting Default De

Setting Default DescriptionWEP Key RotationInterval300Sets the frequency at which the Wired Equivalent Privacy (WEP) keysare rotated in the device gro

95 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User GuideSetting Default DescriptionEncryption Modes: Require 802.1X, Option

Setting Default DescriptionEncryption Mode WPA2/PSKWPA2 WPACompatibility ModeYesSpecify whether to enable WPA2 WPA Compatibility Mode.WPA1 Cipher(Cisc

97 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User Guide1. Go to Groups > List and select the group name for which to de

Setting Default DescriptionSpecify Interface Name YesEnables or disables an interface name for the VLAN interface.Selecting No for this option display

99 | Configuring and Using Device Groups Dell Networking W-AirWave 8.0 | User GuideSetting Default DescriptionEncryption ModeNoEncryptionDrop-down men