Dell OptiPlex E1 User Manual Page 46
- Page / 88
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Windows NT 4.0 NIC
NOTE: If you are installing the Windows NT 4.0 operating system for the first time, you must install Windows NT 4.0
Service Pack 3 and the bus-mastering enhanced integrated drive electronics (EIDE) device drivers prior to installing the
Windows NT 4.0 NIC driver.
To connect your system to, and configure it for use on, an Ethernet network, follow these steps:
1. Use the Program Diskette Maker (located in the Dell Accessories folder) to make a diskette copy of the NIC drivers
installed on your hard-disk drive.
2. Connect the network cable to the back of your computer.
See "
Network Cable Requirements" found earlier in this section for more information.
3. Verify that the NIC is enabled in the System Setup program.
See "
Using the System Setup Program," for more information.
4. Start Windows NT 4.0, and log in as user Administrator or as a user with Administrator privileges.
For information on administrative users and privileges, see your Windows NT documentation.
5. Double-click My Computer, double-click Control Panel, and then double-click the Network icon.
NOTE: If you are installing networking on your system for the first time, Win-dows NT displays a message asking
if you want to install networking. Click Yes, and refer to your Windows NT documentation for instructions.
6. Click the Adapters tab in the Network Control Panel, and then click Add to access the Select Network Adapter
window.
7. Click Have Disk.
8. Insert diskette 2 into drive A, type a:\, and then click OK.
9. Select 3Com Fast EtherLink/EtherLink XL PCI Bus-Master NIC
(3C905B-TX), and then click OK.
10. When prompted for diskette 2, click OK.
11. When the operating system has finished copying files from diskette 2, click Close in the Windows Welcome screen
and remove the diskette from drive A. Then click Close in the Network window.
12. When prompted, enter information about your specific network.
See your system administrator for information.
13. Click Yes in the Network Settings Change window to restart your system.
Windows NT 3.5x NIC
To connect your system to, and configure it for use on, an Ethernet network, follow these steps:
1. Use the Program Diskette Maker (located in the Dell Accessories program group) to make a diskette copy of the NIC
drivers installed on your hard-disk drive.
2. Connect the network cable to the back of your computer.
See "
Network Cable Requirements" found earlier in this section for more information.
3. Verify that the NIC is enabled in the System Setup program.
- System Features 2
- Hardware Features 3
- Dell OpenManage Program 5
- Wakeup On LAN 6
- Auto Power On 7
- Chassis Intrusion 7
- Passwords 7
- Using the Power Switch 8
- Energy Star Compliance 8
- Getting Help 10
- Overview 12
- System Setup Screen 13
- System Setup Categories 14
- System Date 15
- Hard-Disk Drive Sequence 17
- Boot Sequence 17
- Reserved Memory 18
- CPU Speed 18
- Integrated Devices 18
- System Memory 18
- Video Memory 18
- System Security 20
- Keyboard NumLock 21
- Asset Tag 23
- System Data Categories 24
- Responding to Error Messages 29
- OptiPlex 30
- E1 Managed 30
- About the ICU 31
- When to Run the ICU 32
- Preparing to Use the ICU 32
- Starting the ICU 33
- Adding a Listed Card 34
- Adding an Unlisted Card 37
- Modifying a Card 39
- Removing a Card 40
- Viewing Resources 40
- Exiting From the ICU 41
- Locking and Unlocking Cards 42
- Video Controller 44
- Audio Controller 44
- Network Cable Requirements 45
- Configuring the NIC 45
- Windows NT 3.5x NIC 46
- Windows 95 NIC 47
- Windows for Workgroups NIC 48
- MS-DOS NIC 48
- Before You Begin 50
- Removing the Computer Cover 51
- Replacing the Computer Cover 51
- Inside Your Computer 52
- Switches 54
- Expansion Cards 58
- Expansion Slots 59
- Installing an Expansion Card 59
- Removing an Expansion Card 61
- Adding Memory 62
- Performing a Memory Upgrade 63
- Adding Video Memory 65
- Replacing the System Battery 66
- Connecting Drives 69
- ICU Error Messages 81
- Could not 86
- Boot Device 88
Related products and manuals for Computers Dell OptiPlex E1
Computers Dell PowerEdge M805 User Manual
(808 pages)
(808 pages)
Computers Dell PowerEdge R410 User Manual
(10 pages)
(10 pages)
Computers Dell Dimension L___cx User Manual
(46 pages)
(46 pages)
Computers Dell OptiPlex Gxi User Manual
(126 pages)
(126 pages)
Computers Dell Dimension 4500S User Manual
(132 pages)
(132 pages)
Computers Dell OptiPlex GX270 User Manual
(38 pages)
(38 pages)
(2 pages)© 2020, manymanuals.com. All rights reserved. | 0.468 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals