Dell PowerConnect 5212 Specifications Page 57
- Page / 110
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Console(config-if)#switchport acceptable-frame-types tagged
Console(config-if)#switchport ingress-filtering
Console(config-if)#
Trunk Settings
On the Trunk Settings page, you can specify the default port VLAN ID (PVID) for ports that are configured as trunk members. When an untagged packet
enters the switch, it is, by default, tagged with the ID specified by the port's PVID.
For each trunk listed in the Trunk column, the following options are available:
l PVID — Specifies the VLAN ID assigned to untagged frames received on the trunk. (Default: 1)
l Acceptable Frame Type — Sets the trunk to accept all frame types, including VLAN tagged or untagged frames, or only tagged frames. When set to
receive all frame types, any received frames that are untagged are assigned to the default VLAN. (Options: ALL, Tagged; Default: ALL)
l Ingress Filtering — If ingress filtering is enabled, incoming frames for VLANs which do not include this trunk in their member set will be discarded at the
ingress port. (Default: Disabled)
l Note the following points about ingress filtering:
¡ Ingress filtering only affects tagged frames.
¡ If ingress filtering is disabled, the trunk will accept any VLAN-tagged frame if the tag matches a VLAN known to the switch (except for those
VLANs explicitly forbidden on this trunk).
¡ If ingress filtering is enabled, the trunk will discard incoming frames tagged for VLANs which do not include this ingress port in their member set.
¡ Ingress filtering does not affect VLAN independent BPDU frames, such as GVRP or STP. However, they do affect VLAN dependent BPDU frames,
such as GMRP.
l GVRP Status — Enables/disables GVRP for the trunk. GVRP defines a way for switches to exchange VLAN information to automatically register VLAN
members on ports across the network. GVRP must be globally enabled for the switch before you can individually enable GVRP for a specific trunk. For
more information, see "GVRP." (Default: Disabled)
l GARP Join Timer — Specifies the interval (in centiseconds) between transmitting requests/queries to participate in a VLAN group. (The range is 20 to
1000 centiseconds.)
l GARP Leave Timer — Specifies the interval (in centiseconds) that a trunk waits before leaving a VLAN group. GARP Leave Timer should be set to more
than twice the join time. This interval ensures that after a Leave or LeaveAll message has been issued, the applicants can rejoin before the trunk
actuallyleavesthegroup.(Therangeis60to3000centiseconds.)
l GARP LeaveAll Timer —Specifies the interval (in centiseconds) between when a LeaveAll query message for VLAN group participants is sent and when
the trunk leaves the group. This interval should be considerably larger than the Leave Time to minimize the amount of traffic generated by nodes
rejoining the group. (The range is 500 to 18000 centiseconds.)
l Mode – Indicates the VLAN membership mode for a trunk.
(Default: Hybrid)
¡ 1Q Trunk – Specifies a port as an end point for a VLAN trunk. A trunk is a direct link between two switches, so the port transmits tagged frames
that identify the source VLAN.
¡ Hybrid – Specifies a hybrid VLAN interface. The trunk may transmit tagged or untagged frames.
To save any changes you make in this page, click Apply Changes. If you don't want to save the changes, click Refresh.
NOTICE: If a trunk is not a member of VLAN 1 and you assign its PVID to this VLAN, the trunk will automatically be added to VLAN 1 as an untagged
member. For all other VLANs, a trunk must first be configured as an untagged member before you can assign its PVID to that group.
NOTICE: If Mode is set to 1Q Trunk, frames belonging to the trunk's default VLAN (i.e., associated with the PVID) are sent untagged, but all other
frames are tagged with the assigned VLAN ID.
- Introduction 2
- Front-Panel Components 3
- Back-Panel Descriptions 4
- Management 4
- Installation 6
- Connecting the Console Port 7
- Password Protection 7
- SNMP Settings 8
- IP Address Assignment 8
- Management Interface 11
- General Information 12
- Example 13
- CLI Commands 13
- Versions 16
- System Logs Configuration 18
- Remote Logs Configuration 20
- IP Address 22
- Security 24
- Authentication Settings 27
- Jumbo Frame 30
- Firmware Upgrade 31
- Configuration 33
- Port Configuration 36
- Trunk Configuration 38
- Broadcast Control 40
- Port Mirroring 41
- Port Security 42
- Address Table 44
- Dynamic Addresses 45
- Address Aging 46
- Spanning Tree 47
- Bridge Settings 48
- Advanced Bridge Settings 50
- Port and Trunk Settings 51
- VLAN Membership 53
- Removing VLAN Membership 54
- Port Settings 55
- Trunk Settings 57
- Class of Service 59
- Traffic Classes 60
- Queue Scheduling 62
- Layer 3/4 Priority 63
- IP Precedence 64
- DSCP Priority 64
- Link Aggregation 67
- Communities 69
- IP Filtering 71
- Multicast Support 72
- IGMP Member Port Table 74
- Statistics 77
- Utilization Summary 80
- Counter Summary 80
- VLANs and Frame Tagging 84
- VLAN Configuration 84
- Automatic VLAN Registration 85
- VLAN Examples 86
- Example 2 87
- Back to Contents Page 90
- Appendix 91
- Management VLAN Access 92
- Technical Specifications 95
- Getting Help 95
- Problems With Your Order 96
- Product Information 97
- Before You Call 97
- Contacting Dell 97
- Regulatory Notices 104
- IC Notice (Canada Only) 105
- CE Notice (European Union) 105
- VCCI Notice (Japan Only) 105
- General 107
- Rack Mounting of Systems 108
Related products and manuals for Network switches Dell PowerConnect 5212
Network switches Dell C300 Specifications
(74 pages)
(74 pages)
Network switches Dell M2401G User Manual
(27 pages)
(27 pages)
Network switches Dell S25P Specifications
(18 pages)
(18 pages)
Network switches Dell DF10MXL Specifications
(38 pages)
(38 pages)
Network switches Dell S25V Specifications
(26 pages)
(26 pages)
© 2020, manymanuals.com. All rights reserved. | 0.190 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals