Dell OpenManage Server Administrator Version 5.5 User Manual Page 86
- Page / 262
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
86 omconfig: Managing Components Using the Instrumentation Service
Default Warning Thresholds
NOTE: The capabilities for managing sensors vary by systems.
If you want to set both the upper and lower power consumption probe
warning threshold values to the recommended default value, type:
omconfig chassis pwrmonitoring index=0 warnthresh=
settodefault
or
omconfig mainsystem pwrmonitoring index=0
warnthresh=settodefault
You cannot default one value and set another. In other words, if you default
the minimum warning threshold value, you are also selecting the default
value for the maximum warning threshold value.
Specify a Value for Warning Thresholds
If you prefer to specify values for the power consumption probe warning
thresholds, you must specify the number of the probe you are configuring and
the minimum and/or maximum warning threshold value. In the following
example, the probe that is being configured is probe 4:
omconfig chassis pwrmonitoring index=4 warnthresh=
325
or
omconfig mainsystem pwrmonitoring index=4
warnthresh=325.
When you issue the command and the system sets the values you specify, the
following message appears:
Power consumption probe warning threshold(s) set
successfully.
omconfig chassis remoteaccess/omconfig mainsystem remoteaccess
NOTE: This command is applicable to PowerEdge x8xx and x9xx systems only.
Use the omconfig chassis remoteaccess or omconfig mainsystem
remoteaccess command to configure:
• Remote access on a local area network (LAN).
• The serial port for BMC or RAC, whichever is installed.
- Dell™ OpenManage™ 1
- Command Line Interface 1
- User's Guide 1
- Notes and Notices 2
- Contents 3
- 4 Contents 4
- 6 Contents 6
- 8 Contents 8
- 10 Contents 10
- 12 Contents 12
- 14 Contents 14
- Introduction 15
- Primary CLI Commands 16
- Success Messages 18
- Failure Messages 19
- Command Syntax Overview 21
- <n> signauth=< 22
- Using the omhelp Command 23
- Using the omhelp Command 25 25
- 26 Using the omhelp Command 26
- <command level 2> -? 32
- index=n 41
- Commands for Viewing Logs 52
- <component name> 57
- Example Command Output 60
- Processor 61
- Memory Array 62
- Firmware 62
- Network Interface Card 63
- Storage Enclosures 63
- Modular system 65
- Non-modular system 65
- Default Warning Thresholds 86
- NOTE: extimpiusergroup 95
- Defining Alert Actions 102
- Available Alert Actions 103
- (continued) 104
- Example Current Probe Actions 105
- Commands for Clearing Logs 106
- Severity 111
- Example Recovery Commands 113
- Example Shutdown Commands 114
- Ownership Values 117
- Adding Lease Information 122
- Adding Outsource Information 125
- Adding Owner Information 126
- Adding Support Information 128
- Adding System Information 129
- Adding Warranty Information 131
- Using the Storage Management 133
- Command Elements 134
- Commands 138
- NOTE: If a physical disk was 144
- Replacing 144
- ° Celsius 146
- Example Syntax 147
- Complete Syntax 147
- For SAS Controllers 153
- Table 6-18. Size Parameter 155
- RAID 10) 157
- Example for SAS Controllers 173
- ° Celsius, enter: 199
- List (lst) 205
- Table (tbl) 206
- Raw XML (xml) 207
- Custom Delimited Format (cdv) 208
- Glossary 209
- Glossary 209 211
- Glossary 211 213
- Glossary 213 215
- Glossary 215 217
- Glossary 217 219
- Glossary 219 221
- Glossary 221 223
- Glossary 223 225
- Glossary 225 227
- Glossary 227 229
- Glossary 229 231
- Glossary 231 233
- Glossary 235 237
- Glossary 237 239
- •Microprocessor 240
- •Various ROM chips 240
- Glossary 239 241
- • UpperThresholdFatal 241
- • UpperThresholdCritical 241
- • UpperThresholdNon-critical 241
- • LowerThresholdNon-critical 242
- • LowerThresholdCritical 242
- • LowerThresholdFatal 242
- Glossary 241 243
- Glossary 243 245
- Glossary 245 247
- 246 Glossary 248
- Index 247 249
- Index 249 251
- Index 251 253
- Index 253 255
- Index 255 257
- Index 257 259
- Index 259 261
- 260 Index 262
Related products and manuals for NAS & storage servers Dell OpenManage Server Administrator Version 5.5
(80 pages)
NAS & storage servers Dell E03J User Manual
(86 pages)
(86 pages)
NAS & storage servers Dell NX400 Owner's Manual
(123 pages)
(123 pages)
© 2020, manymanuals.com. All rights reserved. | 3.899 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals