Dell OpenManage Server Administrator Version 6.0.1 User Manual Page 97
- Page / 277
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
omconfig: Managing Components Using the Instrumentation Service 97
omconfig chassis pwrmonitoring config=probe index=
0 warnthresh=settodefault
or
omconfig mainsystem pwrmonitoring config=probe
index=0 warnthresh=settodefault
You cannot default one value and set another. If you default the minimum
warning threshold value, you are also selecting the default value for the
maximum warning threshold value.
Specify a Value for Warning Thresholds
If you prefer to specify values for the power consumption probe warning
thresholds, you must specify the number of the probe you are configuring and
the warning threshold value. You can configure the values to be displayed
either in BTU/hr or Watts. In the following example, the probe that is being
configured is probe 4:
omconfig chassis pwrmonitoring config=probe index=
4 warnthresh=325 unit=watt
or
omconfig mainsystem pwrmonitoring config=probe
index=4 warnthresh=325 unit=btuphr.
When you issue the command and the system sets the values you specify, the
following message appears:
Power consumption probe warning threshold(s) set
successfully.
omconfig chassis remoteaccess/omconfig mainsystem remoteaccess
NOTE: This command is applicable to PowerEdge x8xx, x9xx, xx0x, and xx1x
systems only.
Use the omconfig chassis remoteaccess or omconfig mainsystem
remoteaccess command to configure:
• Remote access on a local area network (LAN).
• The serial port for BMC or RAC, whichever is installed.
• The BMC or RAC on a serial over LAN connection.
• Terminal settings for the serial port.
- Dell™ OpenManage™ 1
- Command Line Interface 1
- User's Guide 1
- Notes, Cautions, and Warnings 2
- Contents 3
- 4 Contents 4
- 4 omconfig: Managing 6
- Components Using the 6
- Instrumentation Service 71 6
- Ownership Values 129 8
- 6 Using the Storage 9
- Management Service 147 9
- 10 Contents 10
- 12 Contents 12
- 7 Working With CLI 13
- Command Results 217 13
- Glossary 225 13
- 14 Contents 14
- Introduction 15
- Command Prompts 17
- Primary CLI Commands 17
- Success Messages 18
- Failure Messages 19
- Command Syntax Overview 21
- Using the omhelp Command 23
- Using the omhelp Command 25 25
- 26 Using the omhelp Command 26
- <command level 2> -? 32
- Commands for Viewing Logs 57
- <component name> 61
- Example Command Output 64
- System Attributes 65
- Processor 66
- Memory Array 66
- Firmware 67
- NOTE: This command 75
- NOTE: You cannot 75
- (continued) 100
- NOTE: extimpiusergroup 107
- Defining Alert Actions 114
- Available Alert Actions 115
- Commands for Clearing Logs 118
- Severity 123
- Example Recovery Commands 125
- Example Shutdown Commands 127
- Ownership Values 129
- Adding Lease Information 134
- Adding Outsource Information 137
- Adding Owner Information 138
- Adding Support Information 141
- Adding System Information 143
- Adding Warranty Information 144
- Using the Storage Management 147
- Command Elements 148
- Commands 152
- NOTE: If a physical disk was 158
- Replacing 158
- ° Celsius 160
- Example Syntax 161
- Complete Syntax 161
- For SAS Controllers 167
- Table 6-18. Size Parameter 169
- RAID 10) 171
- Example for SAS Controllers 187
- ° Celsius, enter: 215
- List (lst) 221
- Table (tbl) 222
- Raw XML (xml) 223
- Custom Delimited Format (cdv) 224
- Glossary 225
- Glossary 227 227
- Glossary 229 229
- Glossary 231 231
- Glossary 233 233
- Glossary 235 235
- Glossary 237 237
- Glossary 239 239
- Glossary 241 241
- Glossary 243 243
- Glossary 245 245
- Glossary 247 247
- Glossary 249 249
- Glossary 253 253
- Glossary 255 255
- • Microprocessor 256
- • Various ROM chips 256
- Glossary 257 257
- • UpperThresholdFatal 257
- • UpperThresholdCritical 257
- • UpperThresholdNon-critical 257
- • LowerThresholdNon-critical 258
- • LowerThresholdCritical 258
- • LowerThresholdFatal 258
- Glossary 259 259
- Glossary 261 261
- Glossary 263 263
- 264 Glossary 264
- Index 265 265
- Index 266 266
- Index 267 267
- Index 268 268
- Index 269 269
- Index 270 270
- Index 271 271
- Index 272 272
- Index 273 273
- Index 274 274
- Index 275 275
- Index 276 276
- Index 277 277
Related products and manuals for NAS & storage servers Dell OpenManage Server Administrator Version 6.0.1
(80 pages)
NAS & storage servers Dell E03J User Manual
(86 pages)
(86 pages)
NAS & storage servers Dell NX400 Owner's Manual
(123 pages)
(123 pages)
© 2020, manymanuals.com. All rights reserved. | 1.373 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals