Dell PowerEdge 1750 Service Manual download pdf (Page 10)

Invalid memory configuration detected.

Potential for data corruption exists!

Memory modules are not installed in

matched pairs.

Install memory modules in matched pairs. See "Memory."

Invalid NVRAM configuration, resource re-

allocated

System configuration data has been

ignored.

Check the System Setup configuration settings. See

"Using the System Setup Program."

I/O card parity interrupt at address

Expansion card(s) is improperly installed

or faulty.

Reinstall the expansion card(s). See "Expansion Cards." If

the problem persists, replace the expansion card(s).

Keyboard controller failure

Defective keyboard/mouse controller

(defective system board).

Replace the system board. See "System Board."

Keyboard data line failure

Keyboard stuck key failure

Keyboard clock line failure

Keyboard failure

Keyboard cable connector is loose or

improperly connected; defective

keyboard; defective keyboard/mouse

controller (defective system board).

Check the keyboard cable connection. Replace the

keyboard. If the problem persists, replace the system

board. See "System Board."

Memory allocation error

Memory module(s) is not connected

properly, or an application program or the

operating system failed.

Reseat the modules. See "Memory." Reboot the system. If

the message reappears, see your software

documentation.

Memory address line failure at address, read

value expecting value

Memory high data line failure at start address

to end address

Memory high address line failure at start

address to end address

Memory double word logic failure at start

address to end address

Memory double word logic failure at address,

read value expecting value

Memory odd/even logic failure at start address

to end address

Memory odd/even logic failure at address, read

value expecting value

Memory write/read failure at address, read

value expecting value

Memory write/read failure at start address to

end address

Faulty or improperly seated memory

modules or defective system board.



Remove and reseat the memory modules. See "Memory."

If the problem persists, replace the memory modules. If

the problem persists, replace the system board. See

"System Board."

Memory parity failure at start address to end

address

Memory parity error at address

Improperly seated or faulty memory

modules.

Remove and reseat the memory modules. See "Memory."

If the problem persists, replace the memory modules.

No boot device available

Faulty diskette, diskette/CD drive

subsystem, hard drive, or hard-drive

subsystem; no boot disk in drive A.

Replace the diskette. Replace the diskette drive or the

hard drive. See "Installing a Diskette Drive" or "Internal

SCSI Hard Drives." If the problem persists, replace the

system board. See "System Board."

No boot sector on hard- disk

No operating system on the hard drive.

Check the hard-drive configuration settings in the System

Setup program. See "Using the System Setup Program."

No timer tick interrupt

Defective system board.

Replace the system board. See "System Board."

No PXE-capable device available

<F12> was pressed during POST and no

PXE devices are detected.

Check the cables connected to the NICs. Check the

configuration settings in the System Setup program for

the NICs. See "Using the System Setup Program."

Non-system disk or disk error

Faulty diskette, diskette drive subsystem,

or hard-drive subsystem.

Replace the diskette. Reseat all drives and reboot the

system. If the error message reappears, replace the

system board. See "System Board."

Not a boot diskette

No operating system on diskette.

Use a bootable diskette.

PCI BIOS failed to install

PCI device (option ROM) checksum failure

is detected during shadowing.

Contact the PCI device manufacturer to obtain a suitable

replacement PCI option ROM. Follow the manufacturer's

instructions to install the option ROM.

Plug & Play Configuration Error

Error encountered when initializing the

PCI device, or the system board is

defective.

Install the NVRAM_CLR jumper and reboot the system.

See Figure5-2 for jumper location. If the problem

persists, replace the system board. See "System Board."

Plug & Play Configuration Error PCI_n

Error encountered when initializing the

PCI adapter.

Install the NVRAM_CLR jumper and reboot the system.

See Figure5-2 for jumper location. If the problem

persists, replace the specified expansion card. See

"Expansion Cards." If the problem persists, replace the

system board. See "System Board."

Primary backplane error

Improperly attached or missing

backplane.

Ensure that the SCSI backplane board is fully seated. See

"SCSI Backplane Board."

Primary IDE device 0 not found

Primary IDE device 1 not found

Improperly connected or missing IDE

device.

Ensure that the device's interface cable is securely

connected to the SCSI backplane board. See "Installing a

Diskette Drive" or "Installing a CD Drive." If the problem

persists, replace the device.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 50 51

Comments to this Manuals

No comments

Dell PowerEdge 1750 Service Manual Page 10

Comments to this Manuals

Related products and manuals for Server barebones Dell PowerEdge 1750