Dell PowerEdge 1750 Service Manual download pdf (Page 48)

Integrated Devices Screen

Table6-3 lists the options and descriptions for the information fields that appear on the Integrated Devices screen.



Table 6-3.IntegratedDevicesScreenOptions

Console Redirection Screen

Table6-4 lists the options and descriptions for the information fields that appear on the Console Redirection screen. For more information about using

console redirection, see "Using Console Redirection" in the User's Guide.



Table 6-4.ConsoleRedirectionScreenOptions

System Security Screen

Table6-5 lists the options and descriptions for the information fields that appear on the System Security screen.



Table 6-5.SystemSecurityScreenOptions

Asset Tag

Displays the customer-programmable asset tag number for the system if an asset tag number has been assigned.

Option

Description

Embedded RAID

Controller

Selects between RAID, SCSI, or Off. The configurable options vary, depending on whether the optional ROMB is installed.

l With the ROMB installed — Select either RAID Enabled, SCSI Enabled, or Off.

l Without the ROMB installed — Select either SCSI or Off.

IDE Controller

Enables the integrated IDE CD controller. When set to Auto, each channel of the integrated IDE controller is enabled if IDE devices are

attached to the channel and an external IDE controller is not detected. Otherwise, the channel is disabled.

Diskette Controller

(Auto default)

Enables or disables the system's diskette drive controller. When Auto is selected, the system turns off the controller when necessary to

accommodate a controller card installed in an expansion slot. You can also configure the drive as read-only. When using the read-only

setting, the drive cannot be used to write to a disk.

USB Controller

(On with BIOS

support default)

Enables or disables the system's USB ports. Options are On with BIOS support, On without BIOS support, or Off. Disabling the USB

ports makes system resources available for other devices.

Embedded Gb NIC

1 and NIC 2

Enables or disables the system's integrated NICs. Options are Enabled and Disabled.

NIC 1 PXE

Enables or disables the integrated NIC 1 PXE support. Options are Enabled and Disabled. PXE support allows the system to boot from

the network. Changes take effect after the system reboots.

NIC 2 PXE

Enables or disables the integrated NIC 2 PXE support. Options are Enabled and Disabled. PXE support allows the system to boot from

the network. Changes take effect after the system reboots.

MAC Address

Displays the MAC address for the integrated Gb NIC. This field does not have user-selectable settings.

Serial Port

(Auto default)

Serial port options are COM1, COM3, Auto, and Off.

When the serial port is set to Auto, the integrated port automatically maps to the next available port. The serial port attempts to use

COM1 first, and then COM3. If both addresses are in use for a specific port, the port is disabled.

If you set the serial port to Auto and add an expansion card with a port configured to the same designation, the system automatically

remaps the integrated port to the next available port designation that shares the same IRQ setting.

If you set the serial port to Off, the system automatically remaps the integrated port to the RAC.

Speaker

(On default)

Sets the integrated speaker On or Off. A change to this option takes effect immediately (rebooting the system is not required).

Option

Description

Console Redirection

(Off default)

Sets the console redirection feature to On or Off.

Remote Terminal Type

(VT 100/VT 220 default)

Select either VT 100/VT 220 or ANSI.

Redirection After Boot

(Enabled default)

Enables or disables console redirection after your system restarts.

Option

Description

System

Password

Displays the current status of your system's password security feature and allows you to assign and verify a new system password.

NOTE: See "Using the System Password" for instructions on assigning a system password and using or changing an existing system

password.

Setup

Password

Restricts access to the System Setup program in the same way that you restrict access to your system using the system password feature.

NOTE: See "Using the Setup Password" for instructions on assigning a setup password and using or changing an existing setup password.

1 2 ... 43 44 45 46 47 48 49 50 51

Comments to this Manuals

No comments

Dell PowerEdge 1750 Service Manual Page 48

Comments to this Manuals

Related products and manuals for Server barebones Dell PowerEdge 1750