Dell PowerEdge 4600 User Manual Page 23
- Page / 42
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Back to Contents Page
Using the System Setup Program
Dell™PowerEdge™4600SystemsUser'sGuide
Entering the System Setup Program
System Setup Options
Using the System Password Feature
Using the Setup Password Feature
Disabling a Forgotten Password
Each time you turn on your system, the system compares the configuration of the hardware installed in the system to the hardware listed in the system
configuration information stored in NVRAM on the system board. If the system detects a discrepancy, it generates error messages that identify the incorrect
configuration settings. The system then prompts you to enter the System Setup program to correct the settings.
You can use the System Setup program as follows:
l To change the system configuration information after you add, change, or remove any hardware in your system
l To set or change user-selectable options—forexample,thetimeordateonyoursystem
l To enable or disable any integrated device in your system
After you set up your system, run the System Setup program to familiarize yourself with your system configuration information and optional settings. Print the
System Setup screens (by pressing the <Print Screen> key) or record the information for future reference.
Entering the System Setup Program
Enter the System Setup program as follows:
1. Turn on your system.
If your system is already on, shut it down and then turn it on again.
2. Press <F2> immediately after you see the following message in the upper-right corner of the screen:
<F2> = System Setup
You can also press <F10> to enter Utility Mode or <F12> for PXE Boot. PXE Boot forces a system boot from the network.
If you wait too long and your operating system begins to load into memory, let the system complete the load operation, and then shut down the system
and try again.
You can also enter the System Setup program by responding to certain error messages. See "Responding to Error Messages."
Responding to Error Messages
If an error message appears on your monitor screen while the system is starting up, make a note of the message. Then, before entering the System Setup
program, see "System Beep Codes" and "System Messages" in your Installation and Troubleshooting Guide for an explanation of the message and suggestions
for correcting any errors.
If you are given an option of pressing either <F1> to continue or <F2> to run the System Setup program, press the <F2> key.
Using the System Setup Program
Table3-1 lists the keys that you use to view or change information on the System Setup screens and to exit the program.
NOTE: To ensure an orderly system shutdown, consult the documentation that accompanied your operating system.
NOTE: For help using the System Setup program, press <F1> while in the program.
NOTE: It is normal to receive an error message the first time you start your system after installing a memory upgrade. In that situation, do not refer to
"System Beep Codes" and "System Messages." Instead, see "Adding Memory" in your Installation and Troubleshooting Guide for instructions.)
Table 3-1.SystemSetupNavigationKeys
Keys
Action
Down arrow or <Tab>
Moves to the next field.
Up arrow or <Shift + Tab>
Moves to the previous field.
Left and right arrows or <Space>
Cycles through the settings in a field. In many fields, you can also type the appropriate value.
<Esc>
Exits the System Setup program and restarts the system if any changes were made.
- Notes, Notices, and Cautions 1
- Technical Specifications 2
- I/O Ports and Connectors 4
- Serial Port Connectors 5
- Parallel Port Connector 5
- Keyboard Connector 6
- Video Connector 7
- USB Connectors 8
- The SCSISelect Utility 10
- Boot Device Options 11
- Troubleshooting for NetWare 13
- Back to Contents Page 14
- System Overview 15
- Back-Panel Features 16
- System Features 17
- Power Protection Devices 18
- Other Documents You May Need 18
- Supported Operating Systems 18
- Getting Help 19
- Navigating the CD 20
- Setting Up Your Server 20
- Utility Partition 21
- Asset Tag Utility 21
- System Setup Options 24
- Boot Sequence Screen 25
- Integrated Devices Screen 25
- System Security Screen 25
- Exit Screen 26
- Assigning a System Password 26
- Assigning a Setup Password 27
- Glossary 29
Related products and manuals for Computer hardware Dell PowerEdge 4600
(176 pages)
Computer hardware Dell AX4-5 User Manual
(72 pages)
(72 pages)
Targus THZ06103CA manuales
Manuales del propietario y guías del usuario para Casos de tabletas Targus THZ06103CA.
Ofrecemos 1 manuales en pdf Targus THZ06103CA para descargar gratis por tipos de documentos: Ficha de datos
Comments to this Manuals