Dell PowerEdge 800 Service Manual download pdf (Page 23)

during POST to terminate the

memory test.

No boot device available

Faulty or missing diskette

drive, optical drive, or hard

drive.



Check the Integrated Devices configuration settings in the System Setup

program. See "Using the System Setup Program" in your User's Guide. Ensure

that either SATA Controller, Diskette Controller, or IDE Controller is enabled.

If the system is booting from a SCSI controller, ensure that the controller is

properly connected. If the problem persists, replace the drive. See "Installing

Drives."

No boot sector on hard-disk drive

An operating system is not

on the hard drive.

Check the hard-drive configuration settings in the System Setup program. See

"Using the System Setup Program" in your User's Guide.

No timer tick interrupt

Faulty system board.

See "Getting Help."

Not a boot diskette

Not a bootable diskette.

Use a bootable diskette.

PCI BIOS failed to install

Loose cables to expansion

card(s); faulty or improperly

installed expansion card.

Ensure that all appropriate cables are securely connected to the expansion

cards. See "Troubleshooting Expansion Cards" in "Troubleshooting Your

System."

PCIe Degraded Link Width Error: Embedded

Bus#nn/Dev#nn/Funcn

Expected Link Width is n

Actual Link Width is n

Faulty or improperly installed

PCIe card.

Reseat the PCIe cards. See "Expansion Cards." If the problem persists, see

"Getting Help."

PCIe Degraded Link Width Error: Slot n

Expected Link Width is n

Actual Link Width is n

Faulty or improperly installed

PCIe card in the specified slot

number.

Reseat the PCIe card in the specified slot number. See "Expansion Cards." If

the problem persists, see "Getting Help."

PCIe Training Error: Embedded

Bus#nn/Dev#nn/Funcn

Faulty or improperly installed

PCIe card.

Reseat the PCIe cards. See "Expansion Cards." If the problem persists, see

"Getting Help."

PCIeTrainingError:Slotn

Faulty or improperly installed

PCIe card in the specified slot

number.

Reseat the PCIe card in the specified slot number. See "Expansion Cards." If

the problem persists, see "Getting Help."

Plug & Play Configuration Error

Error encountered in

initializing PCI device; faulty

system board.

Install the NVRAM_CLR jumper and reboot the system. See FigureA-2 for

jumper location. Check for a BIOS update. If the problem persists, see

"Troubleshooting Expansion Cards" in "Troubleshooting Your System." If the

problem persists, see "Getting Help."

Read fault

Requested sector not found

Faulty diskette, diskette

drive, optical drive, or hard

drive.

Replace the diskette. Ensure that the diskette, optical, and hard-drive cables

are properly connected. See "Troubleshooting a Diskette Drive,"

"Troubleshooting an Optical Drive, "Troubleshooting SATA Hard Drives," or

"Troubleshooting SCSI Hard Drives" in "Troubleshooting Your System" for the

appropriate drive(s) installed in your system.

Remote Configuration update attempt

failed

System could not implement

Remote Configuration

request.

Retry Remote Configuration.

ROM bad checksum = address

Faulty or improperly installed

expansion card.

Remove and reseat the expansion cards. See "Troubleshooting Expansion

Cards" in "Troubleshooting Your System."

SATA Port n hard disk not found

SATA hard drive not

connected to port n.

Ensure that the hard-drive cable is properly connected. See "Cabled SATA and

SCSI Hard Drives" in "Installing Drives."

If a drive is not connected to port n, check that the SATA port is disabled in the

System Setup program. See "Using the System Setup Program" in your User's

Guide.

Sector not found

Seek error

Seek operation failed

Faulty diskette or hard drive.

Replace the diskette. If the problem persists, see "Troubleshooting SATA Hard

Drives" or "Troubleshooting SCSI Hard Drives" in "Troubleshooting Your

System" for the appropriate drive installed in your system.

Shutdown failure

Shutdown test failure.

Ensure that all memory modules are properly installed. See "Troubleshooting

System Memory" in "Troubleshooting Your System." If the problem persists, see

"Getting Help."

The amount of system memory has changed.

Faulty memory module.

See "Troubleshooting System Memory" in "Troubleshooting Your System." If the

problem persists, see "Getting Help."



Information only, if you have

changed the memory

configuration.



The amount of tested memory is below the

minimum system configuration. System

halted!

Invalid memory configuration

See "General Memory Module Installation Guidelines" in "Installing System

Components."



Faulty memory module.

See "Troubleshooting System Memory" in "Troubleshooting Your System." If the

problem persists, see "Getting Help."

Time-of-day clock stopped

Faulty battery; faulty system

board.

See "Troubleshooting the System Battery" in "Troubleshooting Your System." If

the problem persists, see "Getting Help."

Time-of-day not set - please run SETUP

program

Incorrect Time or Date

settings; faulty system

battery.

Check the Time and Date settings See "Using the System Setup Program" in

your User's Guide. If the problem persists, see "Troubleshooting the System

Battery" in "Troubleshooting Your System."

Timer chip counter 2 failed

Faulty system board.

See "Getting Help."

Unexpected interrupt in protected mode

Faulty or improperly installed

memory modules or faulty

system board.

Ensure that all memory modules are properly installed. See "General Memory

Module Installation Guidelines" in "Installing System Components." If the

problem persists, see "Troubleshooting System Memory" in "Troubleshooting

Your System." If the problem persists, see "Getting Help."

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 86 87

Comments to this Manuals

No comments

Dell PowerEdge 800 Service Manual Page 23

Comments to this Manuals

Related products and manuals for Servers Dell PowerEdge 800