Dell PowerConnect W-AirWave 7.6 User Manual Page 79
- Page / 332
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Setting Default Description
Bridge
Maximum Age
20
Sets the maximum time, in seconds, that the device stores protocol information. The
supported range is from 6 to 40.
Bridge Hello
Time
2 Sets the time, in seconds, between Hello message broadcasts.
Bridge Forward
Delay
15
Sets the time, in seconds, that the port spends in listening and learning mode if the
spanning tree has changed.
10. To configure Network Time Protocol (NTP) settings locate the NTP section and adjust these settings as
required. Table 45 describes the settings and default values.
Setting Default Description
NTP Server #1,
2,3
None Sets the IP address of the NTP servers to be configured on the AP.
UTC Time Zone 0
Sets the hour offset from UTC time to local time for the AP. Times displayed in AirWave
graphs and logs use the time set on the AirWave server.
Daylight Saving
Time
No
Enables or disables the advanced daylight saving time settings in the Proxim section of the
Groups > Basic configuration page.
Table 45:
NTP Fields and Default Values
11. To configure settings specific to Cisco IOS/Catalyst, locate the Cisco IOS/Catalyst section and adjust these
settings as required. Table 46 describes the settings and default values.
Setting Default Description
SNMP Version 2c The version of SNMP used by AirWave to communicate to the AP.
Cisco IOS CLI
Communication
Telnet
The protocol AirWave uses to communicate with Cisco IOS devices. Selecting SSH
uses the secure shell for command line page (CLI) communication and displays an
SSH Version option. Selecting Telnet sends the data in clear text via Telnet.
Cisco IOS Config File
Communication
TFTP
The protocol AirWave uses to communicate with Cisco IOS devices. Selecting SCP
uses the secure copy protocol for file transfers and displays an SCP Version option.
Selecting TFTP will use the insecure trivial file transfer protocol. The SCP login
and password should be entered in the Telnet username and password fields.
Table 46:
Cisco IOS/Catalyst Fields and Default Values
12. To configure settings specific to Cisco WLC, locate the Cisco WLC section and adjust these settings as
required. Table 47 describes the settings and default values.
Setting Default Description
SNMP Version 2c Sets the version of SNMP used by AirWave to communicate to WLC controllers.
CLI Communication SSH
Sets the protocol AirWave uses to communicate with Cisco IOS devices. Selecting
SSH uses the secure shell for command line page (CLI) communication. Selecting
Telnet sends the data in clear text via Telnet.
Table 47:
Cisco WLC Fields and Default Values
Dell PowerConnect W-AirWave 7.6 | User Guide Configuring and Using Device Groups | 67
- Dell PowerConnect 1
- W-AirWave 7.6 1
- Copyright 2
- Open Source Code 2
- Legal Notice 2
- Contents 3
- Using VisualRF 265 10
- Index 313 11
- Chapter 1 13
- VisualRF 14
- Master Console and Failover 15
- Administrative Roles 16
- Chapter 2 17
- Customizing Columns in Lists 19
- Resetting Pagination Records 20
- Using the Pagination Widget 21
- Customizing the Dashboard 22
- Adding Widgets 23
- Available Widgets 23
- Widget Description 24
- Search Preferences 26
- AMP Setup > General 28
- Table 3: 29
- Table 4: 29
- Top Header Settings 30
- Search Method 30
- Home Overview Preferences 30
- Display Settings 31
- Device Configuration Settings 31
- AMP Features 32
- External Logging Settings 32
- Table 9: 33
- Table 10: 33
- Setting Default Description 34
- Firmware Upgrade Defaults 35
- Additional AMP Services 35
- Performance Settings 36
- Table 14: 38
- Table 15: 38
- Table 16: 38
- Creating AirWave Users 39
- Table 17: 40
- AirWave User Roles 41
- Table 18: 42
- Table 19: 43
- Table 20: 44
- Setting Up Single Sign-On 46
- Table 22: 47
- Table 23: 49
- Table 24: 50
- Table 25: 51
- Table 26: 53
- Table 27: 54
- Table 28: 54
- Table 29: 54
- Table 30: 55
- Table 31: 55
- Table 32: 57
- Setting Up Device Types 58
- Introduction to Cisco WLSE 59
- Initial WLSE Configuration 60
- Managing Devices 61
- Inventory Reporting 61
- Defining Access 61
- Grouping 61
- WDS Participation 61
- Primary or Secondary WDS 62
- Table 34: 63
- Configuring ACS Servers 64
- Table 35: 65
- Table 36: 66
- PCI Auditing 67
- Deploying WMS Offload 69
- Chapter 3 71
- AirWave Groups Overview 72
- Table 38: 73
- Table 39: 75
- Table 40: 76
- Table 41: 77
- Table 42: 77
- Table 43: 78
- Table 44: 78
- Table 45: 79
- Table 46: 79
- Table 47: 79
- Table 48: 80
- Table 49: 80
- Table 50: 81
- Table 51: 82
- Table 52: 83
- Table 53: 85
- Table 54: 87
- Table 55: 87
- Table 56: 88
- Table 57: 89
- Table 58: 89
- Table 59: 89
- Table 60: 91
- Table 61: 92
- Cisco WLC Group Configuration 93
- Table 64: 101
- Table 65: 102
- Table 66: 102
- Table 67: 102
- Comparing Device Groups 104
- Deleting a Group 105
- Modifying Multiple Devices 107
- Table 68: 108
- Action Description 109
- Chapter 4 113
- SNMP/HTTP Scanning 114
- Defining a Scan Set 116
- Running a Scan Set 116
- Table 69: 117
- Table 70: 120
- Adding Universal Devices 123
- Unignoring a Device 124
- Monitoring Devices 125
- Table 71: 127
- Table 72: 129
- Table 73: 130
- Table 74: 131
- Table 75: 131
- Table 76: 132
- Issues Summary section 133
- 802.11 Radio Counters Summary 134
- Recent ARM Events Log 135
- Table 79: 136
- Active BSSIDs Table 137
- Figure 90 138
- Auditing Device Configuration 141
- Configuring AP Settings 145
- Table 81: 146
- Table 82: 148
- Table 83: 149
- Table 84: 150
- Figure 104 153
- Table 85: 155
- Table 86: 157
- Dell PowerConnect W-Series 158
- ArubaOS User Guide 158
- Chapter 5 163
- Viewing and Adding Templates 164
- Table 87: 165
- Table 88: 166
- Configuring General Templates 167
- Using Template Syntax 169
- Using AP-Specific Variables 169
- Push_and_exclude Command 170
- Table 89: 171
- Table 90: 171
- Applying Startup-config Files 174
- WDS Settings in Templates 174
- Configuring a Global Template 178
- Group Name, ssid_1 180
- Subscriber 1, Value 0 180
- Chapter 6 181
- Setting Up RAPIDS 183
- Table 92: 184
- Classification Options 185
- Containment Options 185
- Filtering Options 185
- Defining RAPIDS Rules 186
- Device OUI Score 187
- Rogue Device Threat Level 187
- Table 98: 188
- Table 99: 189
- Recommended RAPIDS Rules 190
- Table 100: 191
- Column Description 192
- Score Override 195
- Using the Audit Log 196
- Additional Resources 197
- Chapter 7 199
- Table 102: 201
- Table 103: 201
- Table 104: 202
- Viewing Triggers 203
- Creating New Triggers 203
- Table 105: 205
- Setting Triggers for Devices 206
- Table 107: 207
- Setting Triggers for Clients 208
- Table 111: 210
- Table 110: 210
- Delivering Triggered Alerts 211
- Viewing Alerts 211
- Responding to Alerts 212
- Overview of the Clients Pages 213
- Table 114: 215
- Field Description 216
- Table 115: 217
- Table 116: 219
- Table 117: 221
- Overview of SOTI MobiControl 226
- Table 118: 227
- Table 119: 229
- The Home > Search Page 232
- Table 121: 235
- Information section: 236
- Table 122: 239
- Table 123: 243
- Backing Up AirWave 244
- Table 124: 245
- Logging out of AirWave 246
- Chapter 8 247
- Table 126: 248
- Using Daily Reports 250
- Using Custom Reports 251
- Table 128: 253
- Table 129: 256
- Table 130: 257
- Table 131: 258
- Using the IDS Events Report 259
- Using the Inventory Report 260
- Using the New Clients Report 262
- Table 133: 263
- Using the Port Usage Report 265
- Using the RF Health Report 267
- Using the VPN Session Report 269
- Defining Reports 270
- Table 134: 271
- Table 135: 272
- Emailing Reports to Smarthost 275
- Chapter 9 277
- Features 278
- Useful Terms 278
- Starting VisualRF 279
- Basic QuickView Navigation 279
- Network View Navigation 280
- Display Menu 281
- Edit Menu 282
- Mesh View Navigation 283
- Server Settings 285
- Location Settings 286
- Table 140: 287
- Attenuation Settings 288
- VisualRF Resource Utilization 289
- Increasing Location Accuracy 293
- Adding Exterior Walls 294
- Figure 208: Drawing a wall 295
- Adding Client Surveys 296
- Adding Regions 297
- Adding a Wiring Closet 298
- Configuring Infrastructure 300
- Tracking Location History 303
- Table 145: 305
- Planning and Provisioning 306
- Creating a New Campus 307
- Table 146: 308
- Importing a Floor Plan 309
- Editing a Floor Plan Image 310
- Sizing a Non-CAD Floor Plan 311
- Error Checking of CAD Images 312
- Tweaking a Planning Region 316
- Auto-Matching Planned Devices 317
- Exporting a campus 318
- Importing from CAD 318
- Batch Importing CAD Files 319
- Post Processing Steps 320
- Common Importation Problems 320
- Pre-Conversion Checklist 320
- VisualRF Location APIs 321
- About VisualRF Plan 322
- VisualRF Plan Installation 323
Related products and manuals for Software Dell PowerConnect W-AirWave 7.6
Software Dell Force10 Z9000 User Manual
(601 pages)
(601 pages)
Software Dell Networking S6000 User Manual
(986 pages)
(986 pages)
Software Dell A02 User's Guide
(38 pages)
(38 pages)
Software Dell Vizioncore User's Guide
(189 pages)
(189 pages)
Software Dell V1.2 User Manual
(224 pages)
(224 pages)
Software Dell Vizioncore User's Guide
(23 pages)
(23 pages)
Software Dell Computer Drive CMC 3.2 User Manual
(292 pages)
(292 pages)
Software Dell Force10 Z9000 User Manual
(937 pages)
(937 pages)
© 2020, manymanuals.com. All rights reserved. | 1.469 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals